mirror of
https://github.com/hanwckf/immortalwrt-mt798x.git
synced 2025-01-10 19:12:33 +08:00
7054721cf9
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Apply this to 21.02 as well to remove an unnecessary backporting pitfall. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 3a4b751110b32380cf827f14a203190cfbc2e40f)
182 lines
3.1 KiB
Plaintext
182 lines
3.1 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar7100.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "aruba,ap-105", "qca,ar7161";
|
|
model = "Aruba AP-105";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,9600";
|
|
};
|
|
|
|
aliases {
|
|
led-boot = &led_power_green;
|
|
led-failsafe = &led_power_red;
|
|
led-running = &led_power_green;
|
|
led-upgrade = &led_power_green;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
extosc: ref {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-output-names = "ref";
|
|
clock-frequency = <40000000>;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power_green: power_green {
|
|
label = "green:power";
|
|
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_power_red: power_red {
|
|
label = "red:power";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
panic-indicator;
|
|
};
|
|
|
|
wifi_2g_red {
|
|
label = "red:wlan2g";
|
|
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wifi_5g_red {
|
|
label = "red:wlan5g";
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
ath9k-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wifi_2g_green {
|
|
label = "green:wlan2g";
|
|
gpios = <&ath9k0 5 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
wifi_5g_green {
|
|
label = "green:wlan5g";
|
|
gpios = <&ath9k1 5 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
i2c {
|
|
compatible = "i2c-gpio";
|
|
|
|
sda-gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
|
scl-gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
tpm@29 {
|
|
compatible = "atmel,at97sc3203s";
|
|
reg = <0x29>;
|
|
|
|
/* triggering it, will also kill system */
|
|
reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
|
|
ath9k0: wifi@0,11 { /* 2.4 GHz */
|
|
compatible = "pci168c,0029";
|
|
mtd-mac-address = <&hwinfo 0x1c>;
|
|
mtd-mac-address-increment = <1>;
|
|
reg = <0x8800 0 0 0 0>;
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
};
|
|
|
|
ath9k1: wifi@0,12 { /* 5 GHz */
|
|
compatible = "pci168c,0029";
|
|
mtd-mac-address = <&hwinfo 0x1c>;
|
|
mtd-mac-address-increment = <2>;
|
|
reg = <0x9000 0 0 0 0>;
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy-mask = <0x1>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
mtd-mac-address = <&hwinfo 0x1c>;
|
|
|
|
pll-data = <0x00110000 0x00001099 0x00991099>;
|
|
|
|
phy-mode = "rgmii";
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "firmware";
|
|
reg = <0x40000 0xfa0000>;
|
|
compatible = "denx,uimage";
|
|
};
|
|
|
|
hwinfo: partition@fe0000 {
|
|
label = "hwinfo";
|
|
reg = <0xfe0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@ff0000 {
|
|
label = "u-boot-env";
|
|
reg = <0xff0000 0x10000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|