mirror of
https://github.com/hanwckf/immortalwrt-mt798x.git
synced 2025-01-10 19:12:33 +08:00
8d9c1087e4
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the device afterwards to boot OpenWRT.
Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
94 lines
1.3 KiB
Plaintext
94 lines
1.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca9557.dtsi"
|
|
|
|
/ {
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "urlader";
|
|
reg = <0x0 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "avm,eva-firmware";
|
|
label = "firmware";
|
|
reg = <0x20000 0xee0000>;
|
|
};
|
|
|
|
partition@f00000 {
|
|
label = "tffs (1)";
|
|
reg = <0xf00000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@f80000 {
|
|
label = "tffs (2)";
|
|
reg = <0xf80000 0x80000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
qca,no-eeprom;
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy0>;
|
|
pll-data = <0x3000000 0x101 0x1313>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
ge0-sgmii = <0>;
|
|
};
|
|
};
|
|
|
|
&mdio1 {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
};
|
|
};
|