08768b44d9
ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7628AN. Specification: - SoC : MediaTek MT7628AN - RAM : DDR2 64 MiB (NT5TU32M16FG-AC) - Flash : SPI-NOR 16 MiB (W25Q128JVSIQ) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7628AN (SoC) - 5 GHz : MediaTek MT7612E - Ethernet : 10/100 Mbps x2 - Switch : MT7628AN (SoC) - LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: 3.3V, GND, TX, RX from "J1" marking - 57600n8 - Power : 12 VDC, 1 A Flash instruction using factory image: 1. Boot WRC-1167FS normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. Wait ~120 seconds to complete flashing Notes: - Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware - Additional padding in factory image is required to avoid incomplete flashing on stock firmware MAC addresses: - LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28 (hex)) - WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22 (hex)) - 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac (text) / Factory, 0x4 (hex)) - 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2 (text) / Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Development
To build your own firmware you need a GNU/Linux, BSD or MacOSX system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
gcc binutils bzip2 flex python3 perl make find grep diff unzip gawk getopt
subversion libz-dev libc-dev rsync
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton freenode.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon freenode.net.
License
OpenWrt is licensed under GPL-2.0