If you want to use the Raspberry Pi UART, "console=serial0,115200" needs
to be removed from the kernel cmdline. This is done by editing
/boot/cmdline.txt. However, this file is not currently backed up during
sysupgrade, so this effectively breaks HATs that require the use of the
UART every sysupgrade.
Backup this file during sysupgrade, and restore it before rebooting.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
As touch creates files with permission 0644 use umask to create
config files with permission 0600 to be inline with INSTALL_CONF
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* compat: support latest suse 15.1 and 15.2
* compat: support RHEL 7.8's faulty siphash backport
* compat: error out if bc is missing
* compat: backport hsiphash_1u32 for tests
We now have improved support for RHEL 7.8, SUSE 15.[12], and Ubuntu 16.04.
* compat: include sch_generic.h header for skb_reset_tc
A fix for a compiler error on kernels with weird configs.
* compat: import latest fixes for ptr_ring
* compat: don't assume READ_ONCE barriers on old kernels
* compat: kvmalloc_array is not required anyway
ptr_ring.h from upstream was imported, with compat modifications, to our
compat layer, to receive the latest fixes.
* compat: prefix icmp[v6]_ndo_send with __compat
Some distros that backported icmp[v6]_ndo_send still try to build the compat
module in some corner case circumstances, resulting in errors. Work around
this with the usual __compat games.
* compat: ip6_dst_lookup_flow was backported to 3.16.83
* compat: ip6_dst_lookup_flow was backported to 4.19.119
Greg and Ben backported the ip6_dst_lookup_flow patches to stable kernels,
causing breaking in our compat module, which these changes fix.
* git: add gitattributes so tarball doesn't have gitignore files
Distros won't need to clean this up manually now.
* crypto: do not export symbols
These don't do anything and only increased file size.
* queueing: cleanup ptr_ring in error path of packet_queue_init
Sultan Alsawaf reported a memory leak on an error path.
* main: mark as in-tree
Now that we're upstream, there's no need to set the taint flag.
* receive: use tunnel helpers for decapsulating ECN markings
ECN markings are now decapsulated using RFC6040 instead of the old RFC3168.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Pulls in workaround for TX rate code firmware bug which might as well
help track it down via different printk()s and thus possibly provide
more clue for proper fix.
Firmware currently sends wrong (0xff) TX rate code which causes
WARN_ONCE, so the workaround just changes this bogus value (0xff) into 0.
For 5.4 it also pulls in tx-queue-wake throttling patch "ath10k: Restart
xmit queues below low-water mark", which should improve performance with
high number of concurrent TCP streams.
Ref: https://github.com/greearb/ath10k-ct/pull/129
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Init script checks for an already active DHCP server on the interface
and if such DHCP server is found, then it logs "refusing to start DHCP"
message, starts dnsmasq without DHCP service unless `option force 1` is
set and caches the DHCP server check result.
Each consecutive service start then uses this cached DHCP server check
result, but doesn't provide log feedback about disabled DHCP service
anymore.
So this patch ensures, that the log message about disabled DHCP service
on particular interface is always provided.
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.
To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Split device-tree of Teltonika RUT955 into a generic RUT9xx part and
a part specific to that version of RUT955 already supported.
Also harmonize GPIO and LED names with what is used by the vendor
firmware and assign RS485 DTR signal.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Due to the switch to DSA, the kernel image has become too big (2641k) for the
kernel partition (2624k) on this device:
WARNING: Image file [...]/linux-kirkwood/linksys_audi-uImage is too big
Disable the device until this is fixed, so buildbots can continue their work.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
undefine was added in make 3.82 which is now some 10 years ago, some
make scripts are beginning to use 'undefine'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This adds some still-missing board names for old TP-Link devices
to ath79 SUPPORTED_DEVICES.
Fixes: FS#3017
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit a1693bf626f8cd00363b0b98642b682522dfcf75.
The rt288x and rt3883 devices in question don't have switches.
Only keep the merged case for rt305x.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
kirkwood has moved to DSA on 5.4, which will make kernel 4.14 and 4.19
support broken on the affected devices.
Support on kernel 5.4 seems to have been running fine for almost 2 months
on multiple devices, while support for 4.19 has never left testing state.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Pawel Dembicki <paweldembicki@gmail.com>
kirkwood has moved to DSA on 5.4, which will make kernel 4.14 and 4.19
support broken on the affected devices.
Support on kernel 5.4 seems to have been running fine for almost 2 months
on multiple devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch removes support for swconfig and switches to dsa driver.
swconfig and switch drivers are removed. DSA driver is enabled and
configuration is adjusted.
In kirkwood only two devices have switches: Linksys EA3500 and EA4500.
WAN MAC configuration in 02_network is required because otherwise WAN
would have the same MAC address as lan interfaces. In swconfig solution
the WAN address was assigned in u-Boot to eth1. Now, as eth1 is disabled
and wan is part of the switch, we have to set it manually.
Compile tested: EA3500, EA4500
Run tested: EA4500
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[minor commit title/message adjustments, remove swconfig package
for devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Backport patch from hostapd.git master that fixes copy/paste error in
crypto_bignum_sub() in crypto_wolfssl.c.
This missing fix was discovered while testing SAE over a mesh interface.
With this fix applied and wolfssl >3.14.4 mesh+SAE works fine with
wpad-mesh-wolfssl.
Cc: Sean Parkinson <sean@wolfssl.com>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
According to a user in OpenWrt forum, on RouterOS the MAC addresses are
ether1(WAN) = MAC
ether2(LAN2) = MAC+1
ether3(LAN3) = MAC+2
etc.
Fix the MAC addresses in OpenWrt.
Ref: https://forum.openwrt.org/t/few-dumb-question-about-mt7530-rb750gr3-dsa/61608
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[remove label_mac in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For wave-2, there is now a new variant: htt-mgt-community (vs the old
full-htt-mgt-community).
The non-full one (hence forth 'diet') compiles out a lot of firmware features
that ath10k does not use. This saves a lot of resources and lets one
configure more stations/vdevs/etc using fwcfg.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
