where to begin? the USB regulator settings were just
a part of the issue. With them changed, according to
the forum it still failed when a USB device was
connected to the port with:
dwc2 4bff80000.usbotg: dwc2_restore_global_registers: no global registers to restore
dwc2 4bff80000.usbotg: dwc2_exit_partial_power_down: failed to restore registers
dwc2 4bff80000.usbotg: exit partial_power_down failed
dwc2 4bff80000.usbotg: HC died; cleaning up
One clue was found upstream in
commit cc10ce0c51b1 ("usb: dwc2: disable power_down on Amlogic devices")
|Disable power_down by setting the parameter to
|DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
|Meson SoCs where USB devices are only recognized when plugged in before
|booting Linux. A hot-plugged USB device was not detected even though the
|device got power (my USB thumb drive for example has an LED which lit
|up).
|[...]
the same method proposed there worked with APM821xx's USB IP-Core.
Link: https://forum.openwrt.org/t/wd-my-book-duo-usb/111926/2
Reported-by: thwe and takimata (openwrt forum)
Fixes: b70d3557e05 ("apm821xx: clean up gpio-hogs")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 832b9cbd741cdb6cc8483b2cddfef6de000ec61d)
The workqueue based implementation has a few corner cases and typically lower
performance than the upstream one
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 01bebc070c35d87c24a594fff7ee1911965759aa)
The following patches were backported from upstream before and are not
needed any more:
package/kernel/mac80211/patches/ath/980-ath10k-fix-max-antenna-gain-unit.patch
package/kernel/mac80211/patches/subsys/307-mac80211-do-not-access-the-IV-when-it-was-stripped.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the dependencies required to run nconfig, also remove outdated
dependencies due to the old version of ubuntu no longer supports
this compilation.
(cherry picked from commit 7c1641b44445f794abf9efd11cca3231b78f52b6)
bootfs still needs more work before it's ready.
For some unknown reason model RAXE500 uses board id RAX220.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 63ba3eaccddeb8058b0fabd69197e650735573bc)
It's needed to support devices with U-Boot. That bootloader passes MTD
layout using cmdline.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 21d28adbc1cc98c55858a73d62b9bf89c3874b08)
It still isn't ready though - more data needs to be added to the bootfs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 494c033f9cbad67ea2cee3860894bdfffea65109)
New BCM4908 family based routers will use U-Boot bootloader. That will
require using a totally different firmware format. Kernel has to be put
in a FIT image.
OpenWrt has some helpers for generating .its files but they don't fit
BCM4908 requirements and there is no simple way of extending any of
them. The best solution seems to be storing an .its template.
BCM4908 bootfs may:
1. contain extra binaries (other than kernel & DTB)
2. include multiple DTB files
3. store device specific U-Boot configurations with custom properties
Such setups are too complex to generate using shell script. Raw .its
file on the other hand seems quire clean & reasonable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a02c971dff934a11ddadf7ffd850dabcab5a3cdf)
Linksys uses an extra 0x100 bytes long tail for BCM4908 images.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit c4d5e60f6115b9a97318774533ea764bf938c2a9)
This simplifies some operations as it doesn't have to be caculated over
and over. It will also allow adding support for more vendor formats.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 063038bcef39802aa65c196a162067f66e5c8621)
List of supported formats grew over time and implementation got a bit
messy. There are multiple functions with format-specific parameters and
commands.
Refactor it by making platform_identify() setup all required info right
after detecting firmware format. This simplifies formats handling in
platform_other_check_image() and platform_do_upgrade() a lot.
This has been tested on:
1. SmartRG SR400ac (TRX): non-NAND sysupgrade
2. Netgear R8000 (CHK): NAND aware and standard sysupgrade-s
3. D-Link DIR-885L (Seama): NAND aware and standard sysupgrade-s
4. Luxul XWR-3150 (LXL): NAND aware and standard sysupgrade-s
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 80041dea7094f46f9ef5402964c95b0a5dcd5f28)
Use "oseama extract" which supports now writing to stdout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e7bd6cce4c382e33a62c462bf07bafba23b22e1a)
Both should be supported since:
1. Adding NVMEM driver for NVRAM
2. Using NVRAM info for determining active firmware partition
Linksys EA9500 uses very similar design and works fine.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 287257d676b1120f388120f1dc259e4eefd3b163)
This includes:
1. BCM5301X changes from 5.14 and queued 5.15 stuff
2. NSP changes from 5.11 - 5.15 for kernel 5.10
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit bce00f47e5d67e5a33e9d7fa137cbe0a5d3d334b)
Port numbers were reverted.
Fixes: c459a6bf482f ("bcm53xx: add support for Luxul FullMAC WiFi devices")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 53546c3e945f5a0a8f8c62311f48c6f21c9ab0a8)
Removed upstreamed:
target/linux/mvebu/patches-5.4/001-PCI-aardvark-Wait-for-endpoint-to-be-ready-before-tr.patch
target/linux/mvebu/patches-5.4/016-PCI-aardvark-Train-link-immediately-after-enabling-t.patch
target/linux/mvebu/patches-5.4/017-PCI-aardvark-Improve-link-training.patch
target/linux/mvebu/patches-5.4/018-PCI-aardvark-Issue-PERST-via-GPIO.patch
target/linux/mvebu/patches-5.4/020-arm64-dts-marvell-armada-37xx-Set-pcie_reset_pin-to-.patch
The following patch does not apply to upstream any more and needs some
more work to make it work fully again. I am not sure if we are still
able to set the UART to a none standard baud rate.
target/linux/ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch
These patches needed manually changes:
target/linux/generic/pending-5.4/110-ehci_hcd_ignore_oc.patch
target/linux/ipq806x/patches-5.4/0065-arm-override-compiler-flags.patch
target/linux/layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch
target/linux/mvebu/patches-5.4/019-PCI-aardvark-Add-PHY-support.patch
target/linux/octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
All others updated automatically.
Compile-tested on: malta/le, armvirt/64, lantiq/xrx200
Runtime-tested on: malta/le, armvirt/64, lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Device specifications
* SoC: QCA9563 @ 775MHz (MIPS 74Kc)
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (EN25QH128)
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9988): a/n/ac, 4x4 MU-MIMO
* IoT Wireless 2.4GHz (QCA6006): currently unusable
* Ethernet (AR8327): 3 LAN × 1GbE, 1 WAN × 1GbE
* LEDs: Internet (blue/orange), System (blue/orange)
* Buttons: Reset
* UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
* Power: 12VDC, 1,5A
MAC addresses map (like in OEM firmware)
art@0x0 88:C3:97:*:57 wan/label
art@0x1002 88:C3:97:*:2D lan/wlan2g
art@0x5006 88:C3:97:*:2C wlan5g
Obtain SSH Access
1. Download and flash the firmware version 1.3.8 (China).
2. Login to the router web interface and get the value of `stok=` from the
URL
3. Open a new tab and go to the following URL (replace <STOK> with the stok
value gained above; line breaks are only for easier handling, please put
together all four lines into a single URL without any spaces):
http://192.168.31.1/cgi-bin/luci/;stok=<STOK>/api/misystem/set_config_iotdev
?bssid=any&user_id=any&ssid=-h%0Anvram%20set%20ssh_en%3D1%0Anvram%20commit
%0Ased%20-i%20%27s%2Fchannel%3D.%2A%2Fchannel%3D%5C%5C%22debug%5C%5C%22%2F
g%27%20%2Fetc%2Finit.d%2Fdropbear%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A
4. Wait 30-60 seconds (this is the time required to generate keys for the
SSH server on the router).
Create Full Backup
1. Obtain SSH Access.
2. Create backup of all flash (on router):
dd if=/dev/mtd0 of=/tmp/ALL.backup
3. Copy backup to PC (on PC):
scp root@192.168.31.1:/tmp/ALL.backup ./
Tip: backup of the original firmware, taken three times, increases the
chances of recovery :)
Calculate The Password
* Locally using shell (replace "12345/E0QM98765" with your router's serial
number):
On Linux
printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \
md5sum - | head -c8 && echo
On macOS
printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \
md5 | head -c8
* Locally using python script (replace "12345/E0QM98765" with your
router's serial number):
wget https://raw.githubusercontent.com/eisaev/ax3600-files/master/scripts/calc_passwd.py
python3.7 -c 'from calc_passwd import calc_passwd; print(calc_passwd("12345/E0QM98765"))'
* Online
https://www.oxygen7.cn/miwifi/
Debricking (lite)
If you have a healthy bootloader, you can use recovery via TFTP using
programs like TinyPXE on Windows or dnsmasq on Linux. To switch the router
to TFTP recovery mode, hold down the reset button, connect the power
supply, and release the button after about 10 seconds. The router must be
connected directly to the PC via the LAN port.
Debricking
You will need a full dump of your flash, a CH341 programmer, and a clip
for in-circuit programming.
Install OpenWRT
1. Obtain SSH Access.
2. Create script (on router):
echo '#!/bin/sh' > /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
echo '. /bin/boardupgrade.sh' >> /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
echo 'board_prepare_upgrade' >> /tmp/flash_fw.sh
echo 'mtd erase rootfs_data' >> /tmp/flash_fw.sh
echo 'mtd write /tmp/openwrt.bin firmware' >> /tmp/flash_fw.sh
echo 'sleep 3' >> /tmp/flash_fw.sh
echo 'reboot' >> /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
chmod +x /tmp/flash_fw.sh
3. Copy `openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin`
to the router (on PC):
scp openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin \
root@192.168.31.1:/tmp/openwrt.bin
4. Flash OpenWRT (on router):
/bin/ash /tmp/flash_fw.sh &
5. SSH connection will be interrupted - this is normal.
6. Wait for the indicator to turn blue.
Signed-off-by: Evgeniy Isaev <isaev.evgeniy@gmail.com>
[improve commit message formatting slightly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6c148116f778bfd2db88476cee4753b32538eafe)
Currently it is not possible to configure VLANs via LUCI on
tplink tl-mr3020-v3. This patch fixes switch topology for the
LUCI interface.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
[copied commit message from github PR]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e22c91e144d63ccbd7b76b370a53652c48db1d6f)
Update busybox to 1.33.2, which includes only 5 commits after 1.33.1
Bug fix release. 1.33.2 has fixes for hush and ash (parsing fixes)
and unlzma (fix where we could read before beginning of buffer).
https://git.busybox.net/busybox/log/?h=1_33_2
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
71e08471ab56 mt76: eeprom: fix return code on corrected bit-flips
9a8fc6636d83 mt76: move sar_capa configuration in common code
7cdbea1dc82a mt76: only access ieee80211_hdr after mt76_insert_ccmp_hdr
678071ef7029 mt76: mt7615: clear mcu error interrupt status on mt7663
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit fc4398fe71810f3bb5637bdfd0b3975a8ec858f0)
a6451fea5a3d mt76: mt7615: improve wmm index allocation
1911486414dc mt76: mt7915: improve wmm index allocation
7998a41d1321 mt76: clear sta powersave flag after notifying driver
664475574438 mt76: mt7603: introduce SAR support
5c0da39c940b mt76: mt7915: introduce SAR support
77fc6c439a32 mt76: mt7603: improve reliability of tx powersave filtering
094b3d800835 firmware: update mt7663 rebb firmware to 20200904171623
25237b19bcc1 mt76: eeprom: tolerate corrected bit-flips
1463cb4c6ac2 mt76: mt7921: fix boolreturn.cocci warning
586bad6020f7 mt76: mt7921: use correct iftype data on 6GHz cap init
8ec95c910425 mt76: mt7921s: fix bus hang with wrong privilege
688e30c7d854 firmware: update mt7921 firmware to version 20211014
6fad970893dd mt76: fix key pointer overwrite in mt7921s_write_txwi/mt7663_usb_sdio_write_txwi
95acf972750c mt76: fix 802.3 RX fail by hdr_trans
3f402b0cf6c0 mt76: mt7921s: fix possible kernel crash due to invalid Rx count
929a03a8d65d mt76: connac: fix last_chan configuration in mt76_connac_mcu_rate_txpower_band
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 7e153900566ec1aebdc4f15f5a9d9ff9b9401cc1)
Also fix typo error which will cause build failed.
Fixes: 75954bd ("default-settings: split cnh variant into a separated pkg")
(cherry picked from commit 202742604b2c0c4620419854e720acf649426036)
