The correct model name of WF-2881 is WF2881 without hyphen. The former used
boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the
sysupgrade-tar image, which is newly added in the previous commit, should
not be used to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WF-2881 sysupgrade image uses UBI rootfs, but still relies on
default_do_upgrade. Because of this, config backup is not restored after
sysupgrade. It can be fixed by switching to nand_do_upgrade and
sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar
properly, so one should use factory image to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Inspired by commit c48b571ad708, add an LED trigger for the WAN LED on top of
the TP-Link TL-WR902AC v1. Currently, only the LED on the port itself shows the
link state, while the LED on top of the device stays dark.
The WAN port of the device is a hybrid LAN/WAN one, hence why the LED at the
port was labeled LAN.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
AR934x chips also got the 'old' qca,ar9330-uart in addition to the
'new' ns16550a compatible one. Add support for UART1 clock selector as
well as device-tree bindings in ar934x.dtsi to make use of that uart.
Reported-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x does not do any harm, so just set
them unconditionally.
Tested-by: Chuanhong Guo <gch981213@gmail.com
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Luxul ABR-4500 and XBR-4500 devices are wired routers with 5 Ethernet
ports and 1 USB 3.0 port. Flashing requires using Luxul firmware 6.4.0
or newer and uploading firmware using "Firmware Update" web UI page.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
This new function make batch processing of network packets possible,
which slightly improves performance.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
XTX XT25F128A shares it's chip ID with XM25QH128A which got identical
features. Hence there it makes no sense to add it to the driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ar933x appears to have the same spi controller as ar934x but it's
not mentioned in datasheet at all. Use new spi driver instead to
gain more flash operating performance.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
A new shift mode was introduced since ar934x which has a way better
performance than current bitbang driver and can handle higher spi
clock properly. This commit adds a new driver to make use of this
new feature.
This new driver has chipselect properly configured and we don't need
cs-gpios hack in dts anymore. Remove them.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit adds the ability to set custom uImage magic to
Build/wr1201-factory-header and renames it to
"Build/custom-initramfs-uimage".
Custom uImage header in initramfs image is required on following
devices:
- I-O DATA WN-AX1167GR2
- I-O DATA WN-AX2033GR
- I-O DATA WN-AX2033GR2
- I-O DATA WN-DX1167R
While at it, fix typo in comment.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[shorten commit title, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
dts file does not need to be executable. 644 is enough.
Fixes: f098c612b6db ("ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
kernel config and patch files do not need to be executable. 644 is enough.
Fixes: 01c8f2e97cc6 ("mediatek: bump to v4.19")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Remove read-only flag from U-boot environment partition for Netgear
WNDR3700 v1 and v2 so u-boot-envtools can modify data there.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Since whole target has been bumped to kernel 4.19 in 01c8f2e97cc6
("mediatek: bump to v4.19") we do not need the overwrite in mt7629
subtarget anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the COMFAST CF-E560AC, an ap143 based
in-wall access point.
Specifications:
- SoC: Qualcomm Atheros QCA9531
- RAM: 128 MB DDR2 (Winbond W971GG6SB-25)
- Storage: 16 MB NOR (Winbond 25Q128JVSO)
- WAN: 1x 10/100 PoE ethernet (48v)
- LAN: 4x 10/100 ethernet
- WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM
- WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM
- USB: one external USB2.0 port
- UART: 3.3v, 2.54mm headers already populated on board
- LED: 7x external
- Button: 1x external
- Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod)
MAC addressing:
- stock
LAN *:40 (label)
WAN *:41
5G *:42
2.4G *:4a
- flash (art partition)
0x0 *:40 (label)
0x6 *:42
0x1002 *:41
0x5006 *:43
This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and
0x5006, however the vendor firmware only reads from art:0x0 for the LAN
interface and then increments in 02_network. They also jump 8 addresses
for the second wifi interface (2.4 GHz). This behavior has been duplicated
in the DTS and ath10k hotplug to align addresses with the vendor firmware
v2.6.0.
Recovery instructions:
This device contains built-in u-boot tftp recovery.
1. Configure PC with static IP 192.168.1.10/24 and tftp server.
2. Place desired image at /firmware_auto.bin at tftp root.
3. Connect device to PC, and power on.
4. Device will fetch flash from tftp, flash and reboot into new image.
Signed-off-by: August Huber <auh@google.com>
[move jtag_disable_pins, remove unnecessary statuses in DTS, remove
duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adapt Netgear WNDR3700v2 device identification string to ath79 naming
scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config,
makefile, init scripts and device tree definition).
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This adds a shared definition Device/tplink-v2 to common-tp-link.mk.
Though currently only one device in ath79 uses it, putting it in
the common file seems more organized. The definitions are based
on the implementation in ramips target, where a lot of devices
is using tplink-v2-* commands already.
The '-V "ver. 2.0"' suffix for Archer D50 v1 can be removed because
it's default in Build/tplink-v2-image anyway.
While at it, add TPLINK_HWREVADD and TPLINK_HVERSION to DEVICE_VARS,
which seems to have been overlooked when adding Archer D50 v1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This renames Device/tplink-loader-okli to Device/tplink-safeloader-okli
since the latter more accurately describes the combination of
tplink-safeloader and loader-okli use there. The old version might
be confused with other uses of the okli loader.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As we have tplink-v2-header and tplink-v2-image recipes as well,
this patch renames the Device/tplink definition to Device/tplink-v1,
as it's using the tplink-v1-* commands. This should provide easier
distinction in the future.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Align subtargets makefiles names to actual subtargets.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This sorts the devices in image Makefiles alphabetically.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fixed sorting in one case, add commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G : *:0F
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Additonal notes
---------------
It is possible to flash back to stock by using tplink-safeloader to create
a sysupgrade image based on a stock update. After the first boot, it is
necessary upgrade to another stock image, otherwise subsequent boots
fail with LZMA ERROR 1 and you have to attach serial to recover the device.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[remove DEVICE_VARS change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the various variants of common device definitions for
TP-Link devices to a common Makefile common-tp-link.mk. This
provides the opportunity to reorganize and move parameters between
individual device definitions and the common ones.
While at it, also use the common definitions for previously
independent definitions where appropriate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I'm having another attempt at trying to getting the 'store dscp into
conntrack connmark' functionality into upstream kernel, since the
restore function (act_ctinfo) has been accepted.
The syntax has changed from 'savedscp' to 'set-dscpmark' since that
conforms more closely with existing functionality.
4.14 backport is more of a hack since the structure versioning
mechanism isn't in place.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This commit adds support for the NanoStation Loco M2/M5 XW devices
on the ath79 target (support was long ago available on ar71xx).
Specifications:
- AR9342 SoC @ 535 MHz
- 64 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- AR8032 switch
- 2T2R 5 GHz radio, 22 dBm
- 13 dBi built-in antenna
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via TFTP:
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
There are several cases where phy-mode and status properties are
set again in DTS(I) files although those were set to the same values
in parent DTSI files already. Remove those cases (and thus also stop
their proliferation by copy/paste).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A minority of ethernet-phy definitions seems to use numbers in label,
name and reg property relatively random. This patch aligns their
use to have the same numeric value for all of them.
While at it, improve order of properties/add newlines for the ethX
nodes where necessary.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The image creation for the mt7623a-rfb-emmc has been removed during
a patch refresh without specific comment. The corresponding base-files
entries and DTS patches for 4.14 are still there.
Since mt7623 is pretty dead and nobody has missed this device, let's
just remove the rest.
Fixes: 050da2107a7e ("mediatek: backport upstream mediatek patches")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: John Crispin <john@phrozen.org>
This converts the TP-Link TL-MR3020v3 board to use the WLAN throughput
LED trigger in order to react to all VAPs.
It also moves the WLAN trigger config of the TP-Link TL-WA801NDv5 to the
DTS and merges the now identical LAN LED configs.
Verified these changes on a TL-MR3020v3.
Signed-off-by: Jan Alexander <jan@nalx.net>
[changed commit title and extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 4716c843d62a5a4c37e7886f54bcf446aa26e786.
Netgear seems to use different partition layouts on the R6260, which
would require us to dynamically detect the position of (at least) the
factory partition.
Revert this fix to avoid breaking existing installations until a better
solution has been worked out.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes support for Teltonika RUT9xx which in recent versions of
the device uses xt25f128b flash.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
DEVICE_PACKAGES is specified twice for the same device. Remove the
first (=older) assignment.
Fixes: 40692f0fb55c ("ramips: mt7620: select only the matching mt76 driver")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This ports the GL.iNet 6408/6416 from ar71xx.
The GL-Connect GL.iNet v1 routers are basically a TP-Link TL-WR710N with
more DRAM/Flash and console/GPIO header in the same small form-factor.
Specifications:
- SoC: Atheros AR9331
- CPU: 400 MHz
- Flash: 8/16 MiB
- RAM: 64 MiB
- WiFi: 2.4 GHz b/g/n (SoC)
- Ethernet: 2x 100M ports (LAN/WAN)
- USB: 1x 2.0
The difference between 6408 and 6416 is just the flash size. It looks like
only the 16 MiB version has been advertised, while the 6408 is a modified
version. There are also 1-port versions sold by third parties.
Installation:
Install the sysupgrade image via stock firmware GUI or upload it via uboot
(web-based). The device will be available at 192.168.1.1.
Attention: In ar71xx, the same board name is used for both flash versions.
So, please make sure you flash the correct ath79 image when upgrading.
This has been device-tested on a GL.iNet 6416.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The EEPROM offset for the NETGEAR R6260 is incorrect, thus no valid
calibration data is used.
Fix this only for the NETGEAR R6260, as it's currently unknown whether
or not other boards are affected.
Signed-off-by: David Bauer <mail@david-bauer.net>
The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a
pocket-size travel router. It is essentially identical to the VIXMINI
(internally referred as MT300N-v3) but with double the RAM and
SPI-flash.
Additionally, set the label-mac for both the VIXMINI as well as the
microuter-N300.
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 128M DDR2
FLASH: 16M
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
