Background radar detection is not supported on devices that
using MT7905, so disable this feature in the following devices:
asus,rt-ax53u
jcg,q20
tplink,eap615-wall-v1
xiaomi,mi-router-cr6606
xiaomi,mi-router-cr6608
xiaomi,mi-router-cr6609
yuncore,ax820
Devices with MT7915 lacking a DFS antenna also do not support
background DFS:
totolink,x5000r
cudy,x6
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 6cbcc34f50a3280f5897a86d69225c081711ca24)
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.
Specifications:
SOC: MT7621 + MT7915
ROM: 128 MiB
RAM: 256 MiB
LED: status *2
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP server IP: 192.168.124.99
MAC Address:
use address(sample 1) address(sample 2) source
label 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 u-boot-env@ethaddr
lan 88:xx:xx:98:xx:13 88:xx:xx:a2:xx:a6 $label +1
wan 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 $label
WiFi4_2G 8a:xx:xx:58:xx:14 8a:xx:xx:52:xx:a7 (Compatibility mode)
WiFi5_5G 8a:xx:xx:b8:xx:14 8a:xx:xx:b2:xx:a7 (Compatibility mode)
WiFi6_2G 8a:xx:xx:18:xx:14 8a:xx:xx:12:xx:a7
WiFi6_5G 8a:xx:xx:78:xx:14 8a:xx:xx:72:xx:a7
Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.
TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
|GND|TX|RX|VCC|
1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
and open a TTL session, enter "reboot", then enter "Y" to confirm.
Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
# tftp 0x80010000 192.168.124.99:initramfs.bin
# bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
partitions if we want to back to stock firmwre due to official
website does not provide download link.
# dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
# dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
# fw_setenv bootargs
# fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
partitions that we backed up in step 4.
# mtd write /tmp/u-boot-env.bin u-boot-env
# mtd write /tmp/firmware.bin firmware
Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 13308161788c98ae6cd48c22b13339fdb8c77130)
These have long been obsolete. For reference, here's the Linux version where
each symbol has been dropped:
CONFIG_IP6_NF_QUEUE - 3.5
CONFIG_IP6_NF_TARGET_LOG - 3.4
CONFIG_IP_NF_MATCH_DSCP - 2.6.19
CONFIG_NF_CONNTRACK_IPV4 - 4.19
CONFIG_NF_CONNTRACK_IPV6 - 4.19
CONFIG_NF_CONNTRACK_RTCACHE - out-of-tree, superseded by flow offloading
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit d7956c57284624f4bc7b905d192c81e1d34576fe)
It isn't used at the moment but let's fix it anyway.
This fixes:
CC drivers/net/dsa/ocelot/felix.o
drivers/net/dsa/ocelot/felix.c:646:22: error: initialization of 'enum dsa_tag_protocol (*)(struct dsa_switch *, int, enum dsa_tag_protocol)' from incompatible pointer type 'enum dsa_tag_protocol (*)(struct dsa_switch *, int)' [-Werror=incompatible-pointer-types]
.get_tag_protocol = felix_get_tag_protocol,
^~~~~~~~~~~~~~~~~~~~~~
for users enabling CONFIG_NET_DSA_MSCC_FELIX.
Fixes: 1f5024aa73fc ("kernel: backport b53/bcm_sf2 changes from v5.6")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Deactivate all the symbols of the B53 DSA driver in the generic kernel
configuration. Multiple targets are now using this drivers and they
only need some of the options.
This fixes the bcm4908 build which didn't deactivate all of the options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit be3fcd72e98844eb12b8dd9ae6c21f4d9c21ac3b)
Fix cannot build: Reference to non-existent node or label
"macaddr_factory_e000" dtb compilation error.
The cherry-pick had to be reworked to use the old mtd-mac-address way as
openwrt-21.02 still wasn't migrated to nvmem implementation.
Fixes: d604032c2a50 ("ramips: fix GB-PC1 and GB-PC2 device support")
Fixes: #11654Fixes: #11385
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
[ rework commit message, add more fixes tag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for EON EN25QX128A spi nor flash with no flags as it does
support SFDP parsing.
Fixes: #9442
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ramips/mt7621: xiaomi_mi-router-4a-gigabit]
(cherry picked from commit d7876daf6552a9f39bd5e0bf50b554e9406ec275)
[ apply the same patch to 5.4 kernel ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
On some of the hardware revisions of Asus RT-AC88U, brcmfmac detects the
4366b1 wireless chip and tries to load the firmware file which doesn't
exist because it's not included in the image.
Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 2b9bb5b187022f8b64c84781c071d6c2b0ce3e45)
The image builds and works fine on Asus RT-AC88U. Therefore, remove the
BROKEN flag from the makefile.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 5c1b1918abf853c95976daf7fea58fb1355eae6d)
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.
Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit f4e219fd5e6cfa33d234dad134fb105cc1620f54)
Asus RT-AC88U is an AC3100 router featuring 9 Ethernet ports over the
integrated Broadcom and the external Realtek switch.
Hardware info:
* Processor: Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
* Switch: BCM53012 in BCM4709C0KFEBG & external RTL8365MB
* DDR3 RAM: 512 MB
* Flash: 128 MB (ESMT F59L1G81LA-25T)
* 2.4GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* 5GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* Ports: 8 Ports, 1 WAN Ports
Flashing instructions:
* Boot to CFE Recovery Mode by holding the reset button while power-on.
* Connect to the router with an ethernet cable.
* Set IPv4 address of the computer to 192.168.1.2 subnet 255.255.255.0.
* Head to http://192.168.1.1.
* Reset NVRAM.
* Upload the OpenWrt image.
CFE bootloader may reject flashing the image due to image integrity check.
In that case, follow the instructions below.
* Rename the OpenWrt image as firmware.trx.
* Run a TFTP server and make it serve the firmware.trx file.
* Run the URL below on a browser or curl.
http://192.168.1.1/do.htm?cmd=flash+-noheader+192.168.1.2:firmware.trx+flash0.trx
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
[rmilecki: mark BROKEN until we sort out nvram & CFE recovery]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 72b9b721d707b7f70109eb70b2a9f22449ceba08)
When we use the internal toolchain USE_SSTRIP will be selected by
default for musl libc and USE_STRIP when glibc is used. Do the same when
an external toolchain is used. USE_GLIBC will also be set for external
toolchain builds based on the EXTERNAL_TOOLCHAIN_LIBC_USE_GLIBC setting.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9403810c020cca136149973a3929bf77a1f501aa)
Expose the SDK options for binary stripping to the menuconfig. This
way, packages can easily be built with debug symbols using the SDK.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit bb817bb4b8b0b546a70e45bd907ebfeea2370dcd)
Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).
Backport upstream commit for its effect on the number of connections per
hashtable bucket.
Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit 15fbb916669dcdfcc706e9e75263ab63f9f27c00)
Add missing define for dwc quirk patch required to fix compilation error
for layerscape target. This was wrongly dropped in a kernel bump.
Fixes: 8e5de897691a ("kernel: bump 5.4 to 5.4.213")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This fixes:
[ 10.440495] bcm_ns_usb2 1800c000.usb2-phy: can't request region for resource [mem 0x1800c000-0x1800cfff]
[ 10.450039] bcm_ns_usb2 1800c000.usb2-phy: Failed to map DMU regs
[ 10.456183] bcm_ns_usb2: probe of 1800c000.usb2-phy failed with error -16
caused by conflict in allocating resources.
Fixes: 44ce70f0e209c ("bcm53xx: drop downstream patch that now breaks pinctrl driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1d7c1a41987ae463700224c08a3629e4086a8f39)
This includes:
1. BCM5301X changes from 5.14 and queued 5.15 stuff
2. NSP changes from 5.11 - 5.15 for kernel 5.10
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit bce00f47e5d67e5a33e9d7fa137cbe0a5d3d334b)
The most affecting change is move of files from bcm4908/ to the bcmbca/.
That required updating few paths.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 45ac906c6415cebd12281088da6b06668c057f0a)
1. Include Linux DTB
2. Add 50991 variant (seems to differ by 1 PHY we don't support yet)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit b8f8c6f2dd8d47216117cb5b78184531ab21dddd)
Add missing define for dwc quirk patch required to fix compilation error
for layerscape target.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
