Ensure the MAC address for all NanoPi R1 boards is assigned uniquely for
each board.
The vendor ships the device in two variants; one with and one without
eMMC; but both without static mac-addresses.
In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S and R4S in case the EEPROM
chip is not present by generating the board MAC from the SD card CID.
[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R1#Hardware_Spec
Similar too and based on:
commit b5675f500daf ("rockchip: ensure NanoPi R4S has unique MAC address")
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Doing a simple ping to my device shows this:
64 bytes from 10.0.253.101: icmp_seq=1 ttl=64 time=2.00 ms
64 bytes from 10.0.253.101: icmp_seq=2 ttl=64 time=2.02 ms
64 bytes from 10.0.253.101: icmp_seq=3 ttl=64 time=1.68 ms
64 bytes from 10.0.253.101: icmp_seq=4 ttl=64 time=1.91 ms
64 bytes from 10.0.253.101: icmp_seq=5 ttl=64 time=1.92 ms
64 bytes from 10.0.253.101: icmp_seq=6 ttl=64 time=2.04 ms
Some users even report higher values on older kernels:
64 bytes from 192.168.1.10: seq=0 ttl=64 time=0.612 ms
64 bytes from 192.168.1.10: seq=1 ttl=64 time=2.852 ms
64 bytes from 192.168.1.10: seq=2 ttl=64 time=2.719 ms
64 bytes from 192.168.1.10: seq=3 ttl=64 time=2.741 ms
64 bytes from 192.168.1.10: seq=4 ttl=64 time=2.808 ms
The problem is that the governor is set to Ondemand, which causes
the CPU to clock all the way down to 48MHz in some cases.
Switching to performance governor:
64 bytes from 10.0.253.101: icmp_seq=1 ttl=64 time=0.528 ms
64 bytes from 10.0.253.101: icmp_seq=2 ttl=64 time=0.561 ms
64 bytes from 10.0.253.101: icmp_seq=3 ttl=64 time=0.633 ms
64 bytes from 10.0.253.101: icmp_seq=4 ttl=64 time=0.526 ms
In theory, using the Performance governor should increase power draw,
but it looks like it really does not matter for this soc.
Using a calibrated precision DC power supply (cpu idle):
Ondemand
24.00V * 0.134A = 3.216 Watts
48.00V * 0.096A = 4.608 Watts
Performance
24.00V * 0.135A = 3.240 Watts
48.00V * 0.096A = 4.608 Watts
Let's simply switch to the Performance governor by default
to fix the general jittery behaviour on devices using this soc.
Tested on: MikroTik wAP ac
Fixes: #13649
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
(cherry picked from commit b8e52852bd62236a2a84663b4592d221ebc64cb4)
The compex WPJ563 actually has both usb controllers wired:
usb0 --> pci-e slot
usb1 --> pin header
As the board exposes it for generic use, enable this controller too.
fixes: #13650
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
(cherry picked from commit 9188c77cbee55a933d0fa75c74e175fbc52c556d)
Adds generic support for sysupgrading on eMMC-based devices.
Provide function emmc_do_upgrade and emmc_copy_config to be used in
/lib/upgrade/platform.sh instead of redundantly implementing the same
logic over and over again.
Similar to generic sysupgrade on NAND, use environment variables
CI_KERNPART, CI_ROOTPART and newly introduce CI_DATAPART to indicate
GPT partition names to be used. On devices with more than one MMC
block device, CI_ROOTDEV can be used to specify the MMC device for
partition name lookups.
Also allow to select block devices directly using EMMC_KERN_DEV,
EMMC_ROOT_DEV and EMMC_DATA_DEV, as using GPT partition names is not
always an option (e.g. when forced to use MBR).
To easily handle writing kernel and rootfs make use of sysupgrade.tar
format convention which is also already used for generic NAND support.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
CC: TruongSinh Tran-Nguyen <i@truongsinh.pro>
(cherry picked from commit 57c1f3f9c5c699cc215bebde772552787c632570)
When the membase and pci_dev pointer were moved to a new struct in priv,
the actual membase users were left untouched, and they started reading
out arbitrary memory behind the struct instead of registers. This
unfortunately turned the RNG into a constant number generator, depending
on the content of what was at that offset.
To fix this, update geode_rng_data_{read,present}() to also get the
membase via amd_geode_priv, and properly read from the right addresses
again.
Closes#13417.
Reported-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Tested-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
(cherry picked from commit 09d13cd8d87cc50fde67bbe81c6cca4b799b2724)
Add spinlock mechanism for mtk_rmw api.
1. When multiple threads operate on the same register resource
which include multiple pins, it will make the register resource
wrong to control. So we add spinlock to avoid this case.
[Release-log]
This patch adds spinlock mechanism to protect mtk_rmw. Without it,
you may suffer from some unexpected problems such as race conidtion
while interrupt occured. And this will lead to pin setting fail.
Hence, we strongly recommand you to merge this patch in your code
base.
Change-Id: I1128dc16cb683b89c2cd9f9138f32552abb00400
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/7962757
Add solution of CH395, which is an ethernet IC chip
from WCH company, to dsa, gsw for mt7981, mt7986.
1. For dsa, CR will be written in mediatek_ge.c
2. For gsw, CR will be written in mt7531.c
3. Enable mt7986 mediatek_ge.c config
[Release-log]
This patch will adjust RX min/max gain. Without this patch,
it may cause a link up fail for CH395 chip under 100Mbps.
In order to enhance the stability of your products,
it's better to merge this patch in your codebase.
Change-Id: If07b4ffc060defb5460ecf98339c1cdd3520a128
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/7858068
Fix the conditions for adding vlan info.
When eth1.x -> wifi, packets cannot be forwarded through the HW path.
(due to with wrong HNAT vlan info)
The patch fix it.
[Release-log]
N/A
Change-Id: Id9e02493157bfc2f3a4dbf046be127cd491f9b17
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/7778652
[Description]
Fix log print level in foe_clear_entry.
There are too many logs when neighbor update,
the logs should be printed on debug level.
[Release-log]
N/A
Change-Id: Ic9b75aa5da33f1ab1f398408811487f72ba9f29b
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/7709249
Those sort out BCM53573 Ethernet info finally.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit ca8868a51127f6081a524d47eab937b90af0bf05)
It seems that DSA-based b53 driver never worked with BCM53573 SoCs and
BCM53125.
In case of swconfig-based b53 this fixes a regression. Switching bgmac
from using mdiobus_register() to of_mdiobus_register() resulted in MDIO
device (BCM53125) having of_node set (see of_mdiobus_register_phy()).
That made downstream b53 driver read invalid data from DT and broke
Ethernet support.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 79fd3e62b4910731c13692b2daa2083e0f95c023)
Basic fan controls are working, including PWM and
tachometer.
RPM target mode is not working yet.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
'help' target fails not finding a file, so follow up on a change[2] made
as a fix for main README[1].
1. d0113711a31f ("README: port to 21st century")
2. 751486b31fd9 ("build: fix README.md reference after rename")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(cherry picked from commit 2d5f7035cf45801158bed6f5d0ac0de0002c1810)
(cherry picked from commit e9911f10e482f3174f745a36c0c9fd7964758caf)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Some device recipes remove default target packages. If user tries to add
them back they will be ignored, since packages list is processed in one
go. Process the device recipe packages first and do user ones later, so
additions won't get filtered out.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(cherry picked from commit e40b9a7fa002154e85459791101a0444d99dfb86)
Fix possibly null pointer and memory leak.
When skb_headroom(skb) < FOE_INFO_LEN, it means that hnat headroom of
the message is incomplete and may have been truncated by other functions.
HNAT should return and not relalloc skb.
If without the patch, may met NULL pointer and memory leak issue.
[Release-log]
N/A
Change-Id: I490191fa2be5fd1d664b228ef7c97951d0efe036
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/7694271
* autocore: remove ethinfo for mtk arm boards
mediatek target uses legacy swconfig which is not supported by autocore.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* mediatek: add support for Livinet ZR-3020
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
---------
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Fix hook drop normal packet
In some cases, the packet match the to the logic
of eth->wlan of the legacy chip(mt7621).
After failing to find the interface,
it will be discarded by the hnat function.
Here packets should be handed over to the kernel
[Release-log]
N/A
Change-Id: Idca4c6e899e743c89fbcb562f2695a77b02a98af
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/7265953
The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX
is the number of firmware upgrades performed by the bootloader. Other bcm63xx
devices rename cferam.000 to cferam.XXX, but this device is special because
the cferam name isn't changed on the first firmware flashing but it's changed
on the subsequent ones.
Therefore, we need to look for "cfe" instead of "cferam" to properly detect
the cferam partition and fix the bootlop.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit cdfcac6e246de9f237d1425e498db3f34ddebbaf)
Some devices rename cferam bootloader using specific patterns and don't follow
broadcom standards for renaming cferam files. This requires supporting
different cferam file names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 8813edd8d9695d4e3939fdaa3c530c682f91de11)
The FriendlyARM NanoPi R4SE is a minor variant of R4S with a on-board eMMC.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 1ef239173c8728e28ee913a333944c5f78276915)
Import commit "ubi: Fix failure attaching when vid_hdr offset equals to
(sub)page size" which did not yet make it to stable upstream Linux trees.
Fixes: #12232Fixes: #12339
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit aad34818b50029e07ed9221ae46f9770d6e29785)
Setting this options modifies the rootfs size of created images. When
installing a large number of packages it may become necessary to
increase the size to have enough storage.
This option is only useful for supported devices, i.e. with an attached
SD Card or installed on a hard drive.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 7b7edd25a571568438c886529d3443054e02f55f)
There's no valid mac address for the second band in the eeprom.
The vendor fw uses 2.4G mac + 4 as the mac for 5G radio.
Do the same in our firmware.
Fixes: 23be410b3d ("ramips: add support for TOTOLINK X5000R")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 212632540043cc9b911c2efb86156479f2710836)
Keep this for shortcut-fe.
This reverts commit cbe73ea33d027dbb4b2cf1eca947ae746119e7d2.
Fixes: #923
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
On any currently supported hardware, the performance impact should not
matter anymore.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 75e78bcaab847557ce1782eb2dea9dff9a029171)
The USB port on the MR8300 randomly fails to feed bus-powered devices.
This is caused by a misconfigured pinmux. The GPIO68 should be used to
enable the USB power (active low), but it's inside the NAND pinmux.
This GPIO pin was found in the original firmware at a startup script in
both MR8300 and EA8300. Therefore apply the fix for both boards.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ed64c3323590e3c9fa8b423bf37689023a7a101f)
Signed-off-by: Steffen Scheib <steffen@scheib.me>
This driver is backported from the v6.0 which deals with
"linux,default-trigger" in leds core. For kernel 5.4 we need
leds-bcm63138 to read trigger on its own.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The hardware of Nokia A-040W-Q and RAISECOM MSG1500 X.00 are
exactly the same, both of which are customized by operators.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 4f9b360f0b9a85202422ef07ee573eeca06d11ab)
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.
Specifications:
- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
- Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
- Switch: 1 * POWER switch
MAC addresses as verified by vendor firmware:
use address source
LAN C8:XX:XX:3A:XX:E7 Config "protest_lan_mac" ascii (label)
WAN C8:XX:XX:3A:XX:EA Config "protest_wan_mac" ascii
5G C8:XX:XX:3A:XX:E8 Factory "0x4" hex
2.4G CA:XX:XX:4A:XX:E8 [not on flash]
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
C8:XX:XX:90:XX:C3 CA:XX:XX:C0:XX:C3 0x30
C8:XX:XX:3A:XX:08 CA:XX:XX:4A:XX:08 0x10
C8:XX:XX:3A:XX:E8 CA:XX:XX:4A:XX:E8 0x10
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Notes:
1. The vendor firmware allows you to connect to the router by telnet.
(known version 1.0.0 can open telnet.)
There is no official binary firmware available.
Backup the important partitions data:
"Bootloader", "Config", "Factory", and "firmware".
Note that with the vendor firmware the memory is detected only 128MiB
and the last 512KiB in NAND flash is not used.
2. The POWER LED is default on after press POWER switch.
The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
The WPS LED is controlled by MT7615DN's GPIO.
Currently there is no proper way to configure it.
3. At the time of adding support the wireless config needs to be set up
by editing the wireless config file:
* Setting the country code is mandatory, otherwise the router loses
connectivity at the next reboot. This is mandatory and can be done
from luci. After setting the country code the router boots correctly.
A reset with the reset button will fix the issue and the user has to
reconfigure.
* This is minor since the 5g interface does not come up online although
it is not set as disabled. 2 options here:
1- Either run the "wifi" command. Can be added from LuCI in system -
startup - local startup and just add wifi above "exit 0".
2- Or add the serialize option in the wireless config file as shown
below. This one would work and bring both interfaces automatically
at every boot:
config wifi-device 'radio0'
option serialize '1'
config wifi-device 'radio1'
option serialize '1'
Flash instructions using initramfs image:
1. Press POWER switch to power down if the router is running.
2. Connect PC to one of LAN ports, and set
static IP address to "10.10.10.2", netmask to "255.255.255.0",
and gateway to "10.10.10.1" manually on the PC.
3. Push and hold the WIFI button, and then power up the router.
After about 10s (or you can call the recovery page, see "4" below)
you can release the WIFI button.
There is no clear indication when the router
is entering or has entered into "RAISECOM Router Recovery Mode".
4. Call the recovery page for the router at "http://10.10.10.1".
Keep an eye on the "WARNING!! tip" of the recovery page.
Click "Choose File" to select initramfs image, then click "Upload".
5. If image is uploaded successfully, you will see the page display
"Device is upgrading the firmware... %".
Keep an eye on the "WARNING!! tip" of the recovery page.
When the page display "Upgrade Successfully",
you can set IP address as "automatically obtain".
6. After the rebooting (PC should automatically obtain an IP address),
open the SSH connection, then download the sysupgrade image
to the router and perform sysupgrade with it.
Flash back to vendor firmware:
See "Flash instructions 1 - 5" above.
The only difference is that in step 4
you should select the vendor firmware which you backup.
Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
(cherry picked from commit bc7d36ba3a43bc3bc4eeab6ea127032aba3e1f4e)
There is a mr25h256 spi flash on this machine. From the mtd backup
of the stock firmware, this spi flash is empty.
[ 3.652745] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16,
fifo:64
[ 3.653925] spi-nor spi0.0: mr25h256 (32 Kbytes)
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit eee41e33eca2f860724bceda3f36ea2e30149ef0)
The problem has been fixed in f47cb405cafd ("ipq806x: fix pci broken
on bootm command"), now the pcie part can be written in the usual way.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
(cherry picked from commit 269758a5bcea1376d037dfea62f161ff8562e489)
This adds support for the Askey RT4230W REV6
(Branded by Spectrum/Charter as RAC2V1K)
At this time, there's no way to reinstall the stock firmware so don't install
this on a router that's being rented.
Specifications:
Qualcomm IPQ8065
1 GB of RAM (DDR3)
512 MB Flash (NAND)
2x Wave 2 WiFi cards (QCA9984)
5x 10/100/1000 Mbps Ethernet (Switch: QCA8337)
1x LED (Controlled by a microcontroller that switches it between red and
blue with different patterns)
1x USB 3.0 Type-A
12V DC Power Input
UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V
Port settings are 115200n8
More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830https://deviwiki.com/wiki/Askey_RAC2V1K
To check what revision your router is, restore one of these config backups
through the stock firmware to get ssh access then run
"cat /proc/device-tree/model".
https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17
The revision number on the board doesn't seem to be very consistent so that's
why this is needed. You can also run printenv in the uboot console and if
machid is set to 177d, that means your router is rev6.
Note: Don't install this if the router is being rented from an ISP. The defined
partition layout is different from the OEM one and even if you changed the
layout to match, backing up and restoring the OEM firmware breaks /overlay so
nothing will save and the router will likely enter a bootloop.
How to install:
Method 1: Install without opening the case using SSH and tftp
You'll need:
RAC2V1K-SSH.zip:
https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip
initramfs and sysupgrade images
Connect to one of the router's LAN ports
Download the RAC2V1K-SSH.zip file and restore the config file that
corresponds to your router's firmware (If you're firmware is newer than what's
in the zip file, just restore the 1.1.16 file)
After a reboot, you should be able to ssh into the router with username:
"4230w" and password: "linuxbox" or "admin". Run the following commannds
fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as
it's in the same subnet as the server
fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next
steps
fw_setenv bootdelay 8
fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq"
Don't reboot the router yet.
Install and set up a tftp server on your computer
Set a static ip on the ethernet interface of your computer (use this for
serverip in the above commands)
Rename the initramfs image to initramfs.bin, and host it with the tftp
server
Reboot the router. If you set up everything right, the router led should
switch over to a slow blue glow which means openwrt is booted. If for some
reason the file doesn't get loaded into ram properly, it should still boot to
the OEM firmware.
After openwrt boots, ssh into it and run these commands:
fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts
mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi
read 0x44000000 kernel 0x6e0000 && bootm"
fw_setenv bootdelay 2
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Method 2: Install with serial access (Do this if something fails and you can't
boot after using method 1)
You'll need:
initramfs and sysupgrade images
Serial access:
https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case
Install and set up a tftp server
Set a static ip on the ethernet interface of your computer
Download the initramfs image, rename it to initramfs.bin, and host it with
the tftp server
Connect the wan port of the router to your computer
Interrupt U-Boot and run these commands:
setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer)
setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet)
setenv bootcmd "setenv mtdids nand0=nand0 &&
set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware
&& ubi read 0x44000000 kernel 0x6e0000 && bootm"
saveenv
tftpboot initramfs.bin
bootm
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Signed-off-by: Lauro Moreno <lmore377@gmail.com>
[add entry in 5.10 patch, fix whitespace issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit da8428d277cd3373b05330cb3b4f93aef717c5ab)