This should slightly improve performance thanks to the better cache
usage.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 6a02205a4d94a7b6a888ec55d1aecd60ebb20d77)
This gets rid of "nvmem-cells" limitation. Dynamic partitions can be
defined for any (sub)partitions layout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 4eda414b09c790344e47c1cebe78e5433b4dc10d)
Enable the AP806's cpufreq driver. This driver is compatible with the
Armada 7K and 8K platforms.
Tested-by: Stijn Segers <foss@volatilesystems.org> (RB5009UG+S+IN)
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
(cherry picked from commit 6f88526fa4e0aa5f60834d181d04f8a9911887be)
ipq806x have different ecc configuration for boot partition and rootfs partition. Add support for this to fix IO error on mtd block scan.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
(cherry picked from commit 62cc66fa6737de50d6aa57042f9508fccd476ed7)
Fixes following missing kernel config symbol after adding GPIO watchdog:
Software watchdog (SOFT_WATCHDOG) [M/n/y/?] m
Watchdog device controlled through GPIO-line (GPIO_WATCHDOG) [Y/n/m/?] y
Register the watchdog as early as possible (GPIO_WATCHDOG_ARCH_INITCALL) [N/y/?] (NEW)
Fixes: 1a97c03d864e ("rampis: feed zbt-we1026 external watchdog")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit fb2801b82c06878ae2ad20b8f95546c34ed3cdf4)
[adapted to config-5.4]
Signed-off-by: Federico Capoano <f.capoano@openwisp.io>
Without feeding the gpio watchdog, the board will reset after 90 seconds
Signed-off-by: Arvid E. Picciani <aep@exys.org>
(cherry picked from commit 1a97c03d864ee5ab917aff2988c62fce223c041e)
[adapted to config-5.4]
Signed-off-by: Federico Capoano <f.capoano@openwisp.io>
Broadcom's U-Boot contains environment data blocks. They need to be
found (offsets aren't predefined) to access env variables.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 137149847d0f374515f38952ce0986b03a97f2e4)
Backport upstream solution that permits to declare nvmem cells with
dynamic partition defined by special parser.
This provide an OF node for NVMEM and connect it to the defined dynamic
partition.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1a9ee367343edce263f82cc91a49d796c9d45ea3)
Serge Vasilugin reports:
To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
a) RF and BBP regs never be corrected for this mode
b) eLNA is driven the same way as ePA with mt7620's pin PA
but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
so I'm not sure that request for pa_pin in dts-file will be enough
First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA
Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
35-40/30-35 Mbps for HT20
65-70/60-65 Mbps for HT40
Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 31a6605de04218e1c04bd5c2436c24d7d1c07506)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This fixes:
[ 0.292536] ns-pinmux 1800c100.cru:pinctrl: invalid resource
[ 0.298322] ns-pinmux 1800c100.cru:pinctrl: Failed to map pinctrl regs
[ 0.305578] ns-pinmux: probe of 1800c100.cru:pinctrl failed with error -22
Linux 5.4.157 included commit 6d0b30784fcd9 ("Revert "pinctrl: bcm: ns:
support updated DT binding as syscon subnode"") which makes pinctrl
driver expect the old DT syntax.
Drop downstream patch switching pinctrl node to the invalidated syntax.
Fixes: 0b7311300b01d ("kernel: bump 5.4 to 5.4.158")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
These updates are for kernel 5.15.
Fixes: #778
Fixes: 5765e132a070df ("kernel: igc: sync with upstream updates")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Ensure the MAC address for all NanoPi R4S boards is assigned unique for
each board.
FriendlyElec ship two versions of the R4S: The standard as well as the
enterprise edition with only the enterprise edition including the EEPROM
chip that stores the unique MAC address.
In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S in case the EEPROM chip is not
present by generating the board MAC from the SD card CID.
[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R4S#Differences_Between_R4S_Standard_Version_.26_R4S_Enterprise_Version
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b5675f500daff3ef3f904e53a5566aa7dc09b786)
This updates mac80211 to version 5.15.58-1 which is based on kernel
5.15.58.
The removed patches were applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
It parses U-Boot env data into NVMEM cells.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 34cf31043504473df3174a22d163b71b75e46542)
This is required for non-parser drivers handling MTD devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 41e1e838fbbb0308ad7353a3714e04b8c4585e7e)
