This enables the LEDs on the LAN interfaces.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 1b18195f59b09844ab8fdfd669bc506c25df111b)
Specification:
CPU: Allwinner H5, Quad-core Cortex-A53
DDR3 RAM: 512MB
Network: 10/100/1000M Ethernet x 2
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input
Debug Serial Port: 3Pin pin-header
LED: WAN, LAN, SYS
KEY: Reset
Power Supply: DC 5V/2A
Installation:
Write the image to SD Card with dd.
Note:
1. OpenWrt currently does not support LED_FUNCTION, change back to the
previous practice (Consistent with NanoPi R1).
2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71
("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to
change the phy-mode from rgmii to rgmii-id.
So set phy-mode for 5.4 and 5.10 respectively.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit fde68cb80941a60be93ece75e808b5b407d11cc8)
Merged in https://github.com/u-boot/u-boot/commit/e7510d2,
adjust back to the current 2020.04 version.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit e43eb16efe97a597a2ebaa9f549d1daec2c8c2ab)
945d0d7 utils: fix C style in header file
2cfc26f inittab: detect active console from kernel if no console= specified
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ffeb37047e85a5efd96890db12710e9d60b4b76a)
This adds conflicts between variants of libustream pacakge.
They provide the same file and thus it should not be possible to install
them side by side.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
(cherry picked from commit 219e17a35088a90eea664fbb4c66549d701a3cb4)
All buttons of the FritzBox 7360 family are active-low, not active-high.
Corrent the GPIO flag. This fixes release triggers upon push of a button.
Reported-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 31545378641d45f5fac5ffc408a31b700b80121f)
Apply the same fix that was previously done for the Archer C7v5 to the
A7v5 as well to make the web UI accept our images again.
This is a backport of firmware-utils
commit 84dbf8ee49f522d3a4528763c9473cf3dd7c8c52.
Tested-by: Luflosi <luflosi@luflosi.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
It was reported that some rb912 boards (ar934x) have issues with some ethernet speeds.
Investigation shows that the board failed to adapt the ethernet pll values as shown here:
[ 5.284359] ag71xx 19000000.eth: failed to read pll-handle property
added custom prints in code and triggering a link switch:
[ 62.821446] Atheros AG71xx: fast reset
[ 62.826442] Atheros AG71xx: update pll 2
[ 62.830494] Atheros AG71xx: no pll regmap!
Comparison with another very similar board (rb922 - QCA955x) showed a missing
reference clock frequency in dts, which seems to cause a pll init issue.
Unfortunately, no errors are printed when this occurs.
Adding the frequency property fixes the pll init as it can be parsed now
by the ethernet driver.
[ 55.861407] Atheros AG71xx: fast reset
[ 55.866403] Atheros AG71xx: update pll 2
[ 55.870462] Atheros AG71xx: ath79_set_pllval: regmap: 0x81548000, pll_reg: 0x2c, pll_val: 0x02000000
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 2a000546187122c86143c97337af4d5beacc4908)
Adds support for GPON SFP modules based on the Realtek RTL8672 and
RTL9601C chips, including but not limited to:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1
Signed-off-by: Vladimir Markovets <abam_a@yahoo.com>
(cherry picked from commit f032601ed7d70fe1f468219b68750230b6ea1906)
This allows LEDs to be triggered by custom pattern and not just
predefined ones.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
(cherry picked from commit 507911f477cc29531a2fbdf364df42e7e4f3c696)
The name of the module is 'uleds', not 'leds-uleds'.
Signed-off-by: Evgeny Kolesnikov <evgenyz@gmail.com>
[improve commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3e9318f3c0be1ae14d9d4eb705b02e7441d5d26e)
The allows userspace LEDs to be created and controlled. This can be useful
for testing triggers and can also be used to implement virtual LEDs.
Signed-off-by: Keith T. Garner <kgarner@kgarner.com>
[squash fixup commit and improve option wording]
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 6a37286c2add96dba42fdd285162228eb55a99f1)
The patch
PCI: aardvark: Don't touch PCIe registers if no card connected
was applied into Linux stable version 5.4.163.
Remove it from patches-5.4.
(It applied even though it was applied already, resulting in repeated
code.)
Fixes: 14940aee4566 ("kernel: bump 5.4 to 5.4.163")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This is a bugfix release. Changelog:
*) Avoid loading of a dynamic engine twice.
*) Fixed building on Debian with kfreebsd kernels
*) Prioritise DANE TLSA issuer certs over peer certs
*) Fixed random API for MacOS prior to 10.12
Patches were refreshed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit def9565be632b316c82ffc5a7b28c789e9df75b4)
Right now it includes bcm4908 variant only that is required by BCM4908
family devices with U-Boot.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit f18288e26715f8cdef6c6d62a196dfd4ade8265e)
This is a requirement for backporting DT files defining such LEDs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 85ad48c9579c0482c98fc6b69e885102511e9194)
BCM4908 devices with U-Boot use pkgtb firmware format. It's based on
U-Boot's FIT: DTB with configurations, images & embedded data.
This format contains bootfs, rootfs and optionally a first stage U-Boot
loader. Contained images need to be extracted & flashed.
Broadcom used two sets of firmwares: main & backup. It uses UBI volumes
"metadata1" & "metadata2" for storing U-Boot env variables with info
about flashed images.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 5f05795aa7716879e46fabbd0c51ff20ef9f13bf)
It's very useful flag for handling various formats in sysupgrade. This
commit comes from the 1.34.0 release.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's required by sysupgrade to access UBI metadata partitions.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 444b4ea4a479d76761ee4833cb340b442dac662a)
fdt* utils are needed by targets that use U-Boot FIT images for
sysupgrade. It includes all recent BCM4908 SoC routers as Broadcom
switched from CFE to U-Boot.
fdtget is required for extracting images (bootfs & rootfs) from
Broadcom's ITB. Extracted images can be then flashed to UBI volumes.
sysupgrade is core functionality so it needs dtc as part of base code
base.
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This results in setting format specific data (format info, extract
commands) in a single function. It should help maintaining sysupgrade
code.
This change has been tested on Asus GT-AC5300 and Netgear R8000P.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 30b168b9b8451d6165833cee75019ef7dbfd8a2e)
This helps managing LAN ports.
Ref: https://forum.openwrt.org/t/openwrt-21-02-0-second-release-candidate/98026/121
Fixes: 95b0c07a618f ("ipq40xx: add support for FritzBox 7530")
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 3342d574be08db8926273678291497769d2365e9)
Based on: 1ac627024de9 ("kernel: ath10k-ct: provide a build variant for
small RAM devices")
Like described in the ath10k-ct-smallbuffers version, oom-killer gets
triggered frequently by devices with small RAM.
That change is necessary for many community mesh networks which use
ath10k based devices with too little RAM. The -ct driver has been
proven unstable if used with 11s meshing and only wave2 chipsets are
supporting 11s. Freifunk Berlin is nowadays assembling its
firmware-based completely of vanilla OpenWRT with some package additions
which are made through the imagebuilder. Therefore we cannot take the
approach other freifunk communities have taken to maintain that patch
downstream [1]. Other communities consider these devices as broken and
that change would pretty much give those devices a second life [2].
[1] - 450b306e54
[2] - https://github.com/freifunk-gluon/gluon/issues/1988#issuecomment-619532909
Signed-off-by: Simon Polack <spolack+git@mailbox.org>
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 694757a08f620a9f24b70003542d9dcd0abeac46)
Fix default network configuration of the Puzzle-M902 so all LAN ports
are included in the LAN bridge.
Setup network LED to indicate WAN port link status, like vendor
firmware does as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f9782f5bcd13e419abf9c84017ada27fa9764011)
While on Linux 5.10 this fixes Ethernet link status on all ports and
makes 2.5G ports usable in 2.5G and 1G full-duplex mode, when using
Linux 5.4 and backported Aquantia phy patches, only 1G mode works on
the 2.5G ports and link speed and duplex are not reported correctly
from the phy in case of 2.5G.
The reasons are probably trivial, but hard to find. As having all
ports work at least in 1G speed instead of having them not work at
all is still better, push this anyway for now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f81a06408eec28d479f699bd762b703ac65e2150)
Copy and refresh patch enabling AQR112 and AQR412 Ethernet PHY from
layerscape (5.4) target to mvebu (5.4) as AQR112 can also be found
in IEI Puzzle devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Wire up MCU driver for LEDs, fan and temperature sensor, and add
GPIO reset button just like on the M902 also on the Puzzle M901.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3684b494ddd540b811de44497f0d11309bfd1911)
Add reset button to device tree so it has the function expected from
usual OpenWrt devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ddad936fc60ced1783232af3eddee75347f0d08f)
Set blinking mode using scheduled work instead of blocking which may
result in deadlocks.
Add dynamic kprintf debugging hexdumps of all MCU rx and tx.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7e4c1cca8a137ca4fe5132b8c058e52ba82defac)
Backport MFD driver for communicating with the on-board MCU found on
IEI World Puzzle appliances.
Improve the driver to support multiple LEDs, apply a default state and
let MCU take care of blinking if timing is within supported range.
Wire up LEDs and fan for Puzzle M902 in device tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f0c0b18234418c6ed6d35fcf1c6e5b0cbdceed49
with commit 962c58558010bd302793ac24284c4f9db8fe287f squashed)
When the list of packages to be installed in a built image exceeds a certain
number, then 'opkg install' executed for target '$(curdir)/install' in
package/Makefile fails with: /usr/bin/env: Argument list too long.
On Linux, the length of a command-line parameter is limited by
MAX_ARG_STRLEN to max 128 kB.
* https://elixir.bootlin.com/linux/latest/source/include/uapi/linux/binfmts.h#L15
* https://www.in-ulm.de/~mascheck/various/argmax/
To solve the problem, store the package list being passed to 'opkg install'
in a temporary file and use the shell command substitution to pass the
content of the file to 'opkg install'. This guarantees that the length of
the command-line parameters passed to the bash shell is short.
The following bash script demonstrates the problem:
----------------------------------------------------------------------------
count=${1:-1000}
FILES=""
a_file="/home/egorenar/Repositories/openwrt-rel/bin/targets/alpine/generic/packages/base-files_1414-r16464+19-e887049fbb_arm_cortex-a15_neon-vfpv4.ipk"
for i in $(seq 1 $count); do
FILES="$FILES $a_file"
done
env bash -c "echo $FILES >/dev/null"
echo "$FILES" | wc -c
----------------------------------------------------------------------------
Test run:
----------------------------------------------------------------------------
$ ./test.sh 916
130989
$ ./test.sh 917
./test.sh: line 14: /bin/env: Argument list too long
131132
----------------------------------------------------------------------------
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
[reword commit subject]
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 1854aeec4d37079690309dec3171d0864339f73a)
The http://www.us.tcpdump.org mirror will go offline soon, only use the
normal download URL.
Reported-by: Denis Ovsienko <denis@ovsienko.info>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 18bdfc803bef00fad03f90b73b6e65c3c79cb397)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[rebased for OpenWrt 21.02 branch]
this patch consolidates the amd64-microcode
(moved to linux-firmware.git, previously this was an extra
debian source package download), amdgpu and radeon firmwares
into a shared "amd" makefile.
this will include a microcode update for ZEN 3 CPUs that
came with the 20211216 linux-firmware bump.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit cf8ee49c9bd37ea3e17abe710353737e0f5f9608)
The rtl8723bs firmware was removed and a symlink to the rtl8723bu
firmware was created like it is done in upstream linux-firmware.
The following OpenWrt packages are changing:
* amdgpu-firmware: Multiple updates and new files
* ar3k-firmware: Multiple updates and new files
* ath10k-firmware-qca6174: Updated ath10k/QCA6174/hw3.0/board-2.bin
* bnx2x-firmware: Added bnx2x-e1-7.13.21.0.fw, bnx2x-e1h-7.13.21.0.fw and bnx2x-e2-7.13.21.0.fw
* iwlwifi-firmware-iwl8260c: Updated iwlwifi-8000C-36.ucode
* iwlwifi-firmware-iwl8265: Updated iwlwifi-8265-36.ucode
* iwlwifi-firmware-iwl9000: Updated iwlwifi-9000-pu-b0-jf-b0-46.ucode
* iwlwifi-firmware-iwl9260: Updated iwlwifi-9260-th-b0-jf-b0-46.ucode
* r8169-firmware: Updated rtl8153c-1.fw
* rtl8723bs-firmware: removed
* rtl8723bu-firmware: Added rtlwifi/rtl8723bs_nic.bin symlink
* rtl8822ce-firmware: Updated rtw8822c_fw.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 397dfe4a97e61b87f909181ba60b6187d758635f)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (2012->2021)
