Commit "initramfs: switch to tmpfs to fix ujail" switched initramfs to
now use tmpfs, it causes $(rootfs_type) to now return tmpfs when
running initramfs image instead of being empty.
This broke initramfs detection which prevents config files from
being saved as it does not work from initramfs.
So, lets test for $(rootfs_type) returning "tmpfs" instead.
Fixes: 7fd3c68 ("initramfs: switch to tmpfs to fix ujail)
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit "initramfs: switch to tmpfs to fix ujail" switched initramfs to
now use tmpfs, it causes $(rootfs_type) to now return tmpfs when
running initramfs image instead of being empty.
This broke initramfs detection which is required so that when installing
on MikroTik devices firmware partition would first get erased fully
before writing.
So, lets test for $(rootfs_type) returning "tmpfs" instead.
Fixes: 7fd3c68 ("initramfs: switch to tmpfs to fix ujail)
Signed-off-by: Robert Marko <robimarko@gmail.com>
So we can ship px5g-wolfssl by default in the release image, but still
make the HTTPS for LuCI optional. This small change with addition of
`CONFIG_PACKAGE_px5g-wolfssl=y` into the buildbot's seed config for the
next release should provide optional HTTPS in the next release.
Disabling the current default automatic uhttpd's redirect to HTTPS
should make the HTTPS optional. That's it, user would either need to
switch to HTTPS by manually switching to https:// protocol in the URL or
by issuing the following commands to make the HTTPS automatic redirect
permanent:
$ uci set uhttpd.main.redirect_https=1
$ uci commit uhttpd
$ service uhttpd reload
Signed-off-by: Petr Štetiar <ynezz@true.cz>
MIPS 32 bit support for sanitizer was added with GCC 9, MIPS 64 bit and
ARC are still not supported in GCC 10.
Deactivate them for now and change this when we change the default
compiler to GCC 9 or later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The flash capacity is divided in two flash chips and currently only
first is used. Increase available space for OpenWrt by additional 16 MiB
using mtd-concat driver. Because U-Boot might not be able to load kernel
image spanned through two flash chips, the size of kernel is limited
to space available on first first chip.
Cc: Vladimir Georgievsky <vladimir.georgievsky@yahoo.com>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
AirTight Networks (later renamed to Mojo Networks) C-75 is a dual-band
access point, also sold by WatchGuard under name AP320.
Specification
SoC: Qualcomm Atheros QCA9550
RAM: 128 MiB DDR2
Flash: 2x 16 MiB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled LAN1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: 7x which two are GPIO controlled, four switch controlled, one
controlled by wireless driver
Buttons: 1x GPIO controlled
Serial: RJ-45 port, Cisco pinout
baud: 115200, parity: none, flow control: none
JTAG: Yes, pins marked J1 on PCB
Installation
1. Prepare TFTP server with OpenWrt initramfs-kernel image.
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Power on the device and when prompted to stop autoboot, hit any key.
5. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name>
bootm 0x81000000
6. Wait about 1 minute for OpenWrt to boot.
7. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n /tmp/<openwrt_sysupgrade_image_name>
8. After flashing, the access point will reboot to OpenWrt. Wait few
minutes, until the Power LED stops blinking, then it's ready for
configuration.
Known issues
Green power LED does not work.
Additional information
The U-Boot fails to initialise ethernet ports correctly when a UART
adapter is attached to UART pins (marked J3 on PCB).
Cc: Vladimir Georgievsky <vladimir.georgievsky@yahoo.com>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Adjust spelling of vendor names to what is used in other places.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adjust spelling of vendor name to what is used in other places.
Also move definition in shared section.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These parameters are the same as in vr9.dtsi. This patch removes
redundant parameters.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
7f53d68b1af9 mt76: mt7615: add debugfs knob for setting extended local mac addresses
1a2547b27dfc mt76: do not set NEEDS_UNIQUE_STA_ADDR for 7615 and 7915
2741fd071bb7 mt76: mt7915: support 32 station interfaces
709f2cd77810 mt76: mt7915: fix processing txfree events
434940e08233 mt76: mt7915: measure channel noise and report it via survey
236326896589 mt76: mt7615: retry if mt7615_mcu_init returns -EAGAIN
b5c593b63f4c mt76: mt7663s: move tx/rx processing in the same txrx workqueue
75157b59ae4e mt76: mt7663s: convert txrx_work to mt76_worker
6dc67b058e2a mt76: mt7663s: disable interrupt during txrx_worker processing
b381729626bb mt76: sdio: convert {status/net}_work to mt76_worker
9cb12f7042cc mt76: mt7915: fix DRR sta bss group index
75977a85e844 mt76: mt7915: disable OFDMA/MU-MIMO UL
6cdebe805862 mt76: rename __mt76_mcu_send_msg to mt76_mcu_send_msg
eb9afae96b65 mt76: rename __mt76_mcu_skb_send_msg to mt76_mcu_skb_send_msg
8c73f3b15ada mt76: implement .mcu_parse_response in struct mt76_mcu_ops
fcfbb046c2f3 mt76: move mcu timeout handling to .mcu_parse_response
477caa196ffe mt76: move waiting and locking out of mcu_ops->mcu_skb_send_msg
a4d71501bad6 mt76: make mcu_ops->mcu_send_msg optional
80c310c59ad1 mt76: mt7603: switch to .mcu_skb_send_msg
082b26181013 mt76: implement functions to get the response skb for MCU calls
ee40800df2e4 mt76: mt7915: move eeprom parsing out of mt7915_mcu_parse_response
d33943baac47 mt76: mt7915: query station rx rate from firmware
b8874e8756d9 mt76: add back the SUPPORTS_REORDERING_BUFFER flag
633ae5961db6 mt76: mt7615: enable beacon filtering by default for offload fw
9a203fea3540 mt76: mt7615: introduce quota debugfs node for mt7663s
f9ae638af7e2 mt76: mt7663s: get rid of mt7663s_sta_add
1a5758d894d0 mt76: mt7663s: fix a possible ple quota underflow
dea10c03316f mt76: sdio: get rid of sched.lock
eb4c09957938 mt76: mt7915: set fops_sta_stats.owner to THIS_MODULE
594890b11155 mt76: mt7915: update ppe threshold
8884a5def518 mt76: mt7915: rename mt7915_mcu_get_rate_info to mt7915_mcu_get_tx_rate
33b89f4a1bf4 mt76: set fops_tx_stats.owner to THIS_MODULE
4d019c9672ec sync with upstream changes
35e3cd1db479 mt76: mt7603: fix ED/CCA monitoring with single-stream devices
4f9f79b085b1 wireless: mt76: convert tasklets to use new tasklet_setup() API
20e8cf935ed0 mt76: dma: fix possible deadlock running mt76_dma_cleanup
36089a655f58 mt76: mt7915: fix sparse warning cast from restricted __le16
68c4eedafd61 mt76: fix memory leak if device probing fails
9a1a0a4dec71 mt76: mt7603: add additional EEPROM chip ID
01b943295719 mt76: move mt76_mcu_send_firmware in common module
0aee4999902a mt76: mt7663s: introduce WoW support via GPIO
79ebad117325 mt76: switch to wep sw crypto for mt7615/mt7915
af139725193a mt76: fix tkip configuration for mt7615/7663 devices
664e66b35c0b mt76: mt7615: run key configuration in mt7615_set_key for usb/sdio devices
f675358267d6 mt76: mt76u: rely on woker APIs for rx work
b9f9c16cb1bd mt76: mt76u: use dedicated thread for status work
cdeb1b29cd15 mt76: testmode: switch ib and wb rssi to array type for per-antenna report
0a898c0549b6 mt76: testmode: add snr attribute in rx statistics
3ea9a0433bcc mt76: testmode: add tx_rate_stbc parameter
73427ebbbd27 mt76: testmode: add support for LTF and GI combinations for HE mode
88ebccfe8a39 mt76: mt7915: fix tx rate related fields in tx descriptor
9909c0551e4c mt76: testmode: add support for HE rate modes
03ed0909f922 mt76: mt7915: implement testmode tx support
0aa696834a9c mt76: mt7915: implement testmode rx support
5ed3a34b46ce mt76: mt7915: add support to set txpower in testmode
f86361654e94 mt76: mt7915: add support to set tx frequency offset in testmode
64a765be750a mt76: mt7915: make mt7915_eeprom_read static
9b48c13b52f7 mt76: mt7915: use BIT_ULL for omac_idx
27227fd57ea7 mt76: mt7915: remove unused mt7915_mcu_bss_sync_tlv()
cd795267612d mt76: mt7615: support 16 interfaces
82da525ad0c8 mt76: mt7615: refactor usb/sdio rate code
b9a50da503ad mt76: mt7915: rely on eeprom definitions
c79d18723df0 mt76: move mt76_init_tx_queue in common code
b0b221e91445 mt76: sdio: introduce mt76s_alloc_tx_queue
caba5a99e5ae mt76: sdio: rely on mt76_queue in mt76s_process_tx_queue signature
3ed4aad81ce9 mt76: mt7663s: rely on mt76_queue in mt7663s_tx_run_queue signature
216cf8b28579 mt76: dma: rely on mt76_queue in mt76_dma_tx_cleanup signature
0f9350bef1b5 mt76: rely on mt76_queue in tx_queue_skb signature
8932975be066 mt76: introduce mt76_init_mcu_queue utility routine
b0eb7edcc624 mt76: rely on mt76_queue in tx_queue_skb_raw signature
ccd62467d0f3 mt76: move mcu queues to mt76_dev q_mcu array
2e217fb9e962 mt76: move tx hw data queues in mt76_phy
576647f2ec6a mt76: mt7915: fix endian issues
e881fd67c718 mt76: move band capabilities in mt76_phy
c728cecd7b77 mt76: rely on mt76_phy in mt76_init_sband_2g and mt76_init_sband_5g
231ef27697f9 mt76: move band allocation in mt76_register_phy
8aa24c91b13b mt76: move hw mac_addr in mt76_phy
b436da4d9d92 mt76: mt7915: introduce dbdc support
1e34a02c2dcb mt76: mt7915: get rid of dbdc debugfs knob
d8e681bd3268 mt76: mt7615: fix rdd mcu cmd endianness
19c9e277eff6 mt76: mt7915: fix memory leak in mt7915_mcu_get_rx_rate()
e361b6a71e4b mt76: improve tx queue stop/wake
fb24e5f2305b mt76: mt7915: stop queues when running out of tx tokens
066cc441eb8f mt76: attempt to free up more room when filling the tx queue
93c806a34ec2 mt7915: fix minor issues in the token queue blocking change
c017e329a326 mt76: mt7915: ensure that init work completes before starting the device
9e9da427b8a6 mt76: mt7915: fix polling firmware-own status
5cd805ddfb25 mt76: add more conditions for stopping tx scheduling
aa893c73bf85 mt76: mt7915; increase txq memory limit for non-DBDC 7915 cards to 32 MiB
e44b7c91070e mt76: skip queue stop/wake, rely entirely on txq scheduling
6c6a5c59c101 mt76: mt7915: do not set DRR group for stations
510cb5be1bf7 mt76: usb: remove wake logic in mt76u_status_worker
34f318a25421 mt76: sdio: remove wake logic in mt76s_process_tx_queue
4a90fdf6105e mt76: mt76s: fix NULL pointer dereference in mt76s_process_tx_queue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The PPE only provides a 14 bit hash, however many uses of the skb hash
expect the hash to use the full 32 bit range.
Use jhash to extend the hash to the full size
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The PKG_MIRROR_HASH was not updated when updating the package.
Fixes: f75c70aecaca ("nat46: update to latest git HEAD")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
phy-mode is already set to rgmii for eth0 and sgmii for eth1 in
qca955x.dtsi, no need to do that again in the device DTS files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The GL-MT1300 is a high-performance new generation pocket-sized router
that offers a powerful hardware and first-class cybersecurity protocol
with unique and modern design.
Specifications:
- SoC: MT7621A, Dual-Core @880MHz
- RAM: 256 MB DDR3
- Flash: 32 MB
- Ethernet: 3 x 10/100/1000: 2 x LAN + 1 x WAN
- Wireless: 1 x MT7615D Dual-Band 2.4GHz(400Mbps) + 5GHz(867Mbps)
- USB: 1 x USB 3.0 port
- Slot: 1 x MicroSD card slot
- Button: 1 x Reset button
- Switch: 1 x Mode switch
- LED: 1 x Blue LED + 1 x White LED
MAC addresses based on vendor firmware:
WAN : factory 0x4000
LAN : Mac from factory 0x4000 + 1
2.4GHz : factory 0x4
5GHz : Mac form factory 0x4 + 1
Flashing instructions:
1.Connect to one of LAN ports.
2.Set the static IP on the PC to 192.168.1.2.
3.Press the Reset button and power the device (do not release the button).
After waiting for the blue led to flash 5 times, the white led will
come on and release the button.
4.Browse the 192.168.1.1 web page and update firmware according to web
tips.
5.The blue led will flash when the firmware is being upgraded.
6.The blue led stops blinking to indicate that the firmware upgrade is
complete and U-Boot automatically starts the firmware.
For more information on GL-MT1300, see the OFFICIAL GL.iNet website:
https://www.gl-inet.com/products/gl-mt1300/
Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com>
[add input-type for switch, wrap long line in 10_fix_wifi_mac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The sub target does not support network and there are not so many users
out there, just mark it as source only, so we do jot have to build it.
The quality is not worse than before, it just does not make much sense
to build this automatically.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
