mac80211_get_addr is called from mac80211_generate_mac, where the local variable
initialisation id="${macidx:-0}" suggests that macidx is not always defined.
Probably, idx was supposed to be used instead of $(($macidx + 1)).
Fixes: 4d99db168cf7 ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set")
Signed-off-by: Leon M. George <leon@georgemail.eu>
This option allows adding the ath9k ADC register output as a source
of randomness into the Linux entropy pool at sufficient quality
random data (at least 10 bits and up to 22 bits of min-entropy for
a 32-bit value).
Fixes FS#1444
Signed-off-by: Alan Swanson <reiver@improbability.net>
This patch adds support for 2 new uci sections.
config wifi-vlan
# iface is optional. if it is not defined the vlan will apply
# to all interfaces
option iface default_radio0
option name guest
option vid 100
option network guest
config wifi-station
# iface is optional. if it is not defined the station will apply
# to all interfaces
option iface default_radio0
# mac is optional. if it is not defined it will be a catch all
# for any sta using this key
option mac '00:11:22:33:44:55'
# vid is optional. if it is not defined, the sta will be part of
# the primary iface.
option vid 100
option key testtest
With this patch applied it is possible to use multiple PSKs on a single BSS.
Signed-off-by: John Crispin <john@phrozen.org>
From: Rui Salvaterra <rsalvaterra@gmail.com>
Date: Mon, 25 May 2020 14:49:07 +0100
Subject: [PATCH] rt2800: enable MFP support unconditionally
This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When configuring the radio in legacy mode from luci, the htmode is not set
correctly to NOHT, causing the radio in mesh mode to be set to HT40.
Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
This fixes the following compile error seen on the mpc85xx target:
CC [M] /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o
In file included from /builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/stddef.h:17,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/uapi/linux/wireless.h:77,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/linux/wireless.h:13,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:89:
/builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/alltypes.h:106:15: error: conflicting types for 'ptrdiff_t'
typedef _Addr ptrdiff_t;
^~~~~~~~~
In file included from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/types.h:4,
from ./include/linux/list.h:5,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/list.h:3,
from ./include/linux/module.h:9,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/module.h:3,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:79:
./include/linux/types.h:65:28: note: previous declaration of 'ptrdiff_t' was here
typedef __kernel_ptrdiff_t ptrdiff_t;
^~~~~~~~~
scripts/Makefile.build:265: recipe for target '/linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o' failed
Fixes: 289c6324259e ("mac80211: Update to version 5.7-rc3-1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
The 131-Revert-mac80211-aes-cmac-switch-to-shash-CMAC-driver.patch patch
was manually adapted to the changes in kernel 5.7.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport to the latest minor version.
The removed patch was a backport from the upstream kernel which is now
integrated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The user can now enable the ACK timeout estimation algorithm (dynack)
for drivers that support it.
It is also expected that the distance config accepts the same values as:
$ iw phyX set distance XXX
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
* uci state was not getting reset properly during teardown
* AP+STA co-exist state was not flushed properly upon channel switch
* remove a debug logger call
* properly teardown supplicant instances when they get disabled
* add md5 config support for supplicant
* don't call wpa_supplicant_prepare_interface twice
Signed-off-by: John Crispin <john@phrozen.org>
Before, only frames with a maximum size of 1528 bytes could be
transmitted between two 802.11s nodes.
For batman-adv for instance, which adds its own header to each frame,
we typically need an MTU of at least 1532 bytes to be able to transmit
without fragmentation.
This patch now increases the maxmimum frame size from 1528 to 1656
bytes.
Tested with two ath10k devices in 802.11s mode, as well as with
batman-adv on top of 802.11s with forwarding disabled.
Fix originally found and developed by Ben Greear.
Link: https://github.com/greearb/ath10k-ct/issues/89
Link: 9e5ab25027
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Some FullMAC cfg80211 wireless devices do not support virtual
interfaces, hence there is script logic to keep the existing network
device. Improve this to support renaming the interface if needed and
make sure the existing interface actually belongs to the right phy.
Change calls to 'iw' to avoid outputing warnings and errors to not
confuse users of such devices.
Also bump PKG_RELEASE which has been forgotten in the previous two
mac80211 changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If we know that we have an encrypted link (based on having had
a key configured for TX in the past) then drop all data frames
in the key selection handler if there's no key anymore.
This fixes an issue with mac80211 internal TXQs - there we can
buffer frames for an encrypted link, but then if the key is no
longer there when they're dequeued, the frames are sent without
encryption. This happens if a station is disconnected while the
frames are still on the TXQ.
Detecting that a link should be encrypted based on a first key
having been configured for TX is fine as there are no use cases
for a connection going from with encryption to no encryption.
With extended key IDs, however, there is a case of having a key
configured for only decryption, so we can't just trigger this
behaviour on a key being configured.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Instead of using the actual interface name, a hard-coded 'wlan0' has
slipped into the script. Replace it.
Fixes: ccf2aa9d4b ("mac80211: detect existing interface before adding")
Reported-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The calibration patches for MT7620 unnecessarily export symbols and
populate never accessed function pointers. Remove all that and make
functions static as the only place where each of those functions is
called is within rt2800lib.c.
Also make code more readable by fixing indentation, removing
unnecessary parantheses and simplifying some instructions using
shorthands here and there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Do not export static functions, they are anyway not referenced by any
code in a different module.
This fixes the following compile warning:
WARNING: "rt2800_rf_aux_tx0_loopback" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_write_dc" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_rf_configstore" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_do_sqrt_accumulation" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_rf_configrecover" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_loft_search" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_iq_search" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_setbbptonegenerator" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_rf_aux_tx1_loopback" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Building of ath79-tiny has uncovered following:
Package kmod-rtl8723bs is missing dependencies for the following libraries:
mmc_core.ko
So add this missing dependency.
Fixes: 8c26d67a67d0 ("mac80211: realtek: add staging driver for RTL8723BS SDIO module")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
the code would unconditionally tear down all interfaces upon a reconf.
This should only be done when the reconf call fails.
Signed-off-by: John Crispin <john@phrozen.org>
For virtual access points (when multiple SSIDs are used for one
physical AP), there exist one physical network interface and
multiple virtual interfaces, which are fully under control of
hostapd. When networking is setup, the script
`/lib/netifd/wireless/mac80211.sh` is called, which tries to bring
the interface up by a call to `ip link set dev <iface> up`. This
call might fail for virtual APs, because the virtual interface
might not have been created by hostapd yet. There are some artifical
delays in the script most probably to handle this, but when DFS
channel availability check on 5GHz band is issued, hostapd can
delay creating virtual interfaces by a minute.
In order to fix this (or work around it), do not try to bring the
interface up (this is responsibility of hostapd anyway) and
do not try to set txpower on the virtual interface.
Fixes FS#2698.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
On platforms that do not have CONFIG_MTD enabled, loading the
rt2x00lib kernel module fails because it depends on symbols from
the mtd module ("Unknown symbol get_mtd_device_nm").
This commit disables the code that can read the eeprom from mtd if
mtd is not enabled.
Signed-off-by: Sven Over <sp@cedenti.st>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
