Add support for EON EN25QX128A spi nor flash with no flags as it does
support SFDP parsing.
Fixes: #9442
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ramips/mt7621: xiaomi_mi-router-4a-gigabit]
(cherry picked from commit d7876daf6552a9f39bd5e0bf50b554e9406ec275)
[ apply the same patch to 5.4 kernel ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DMA init timeout in network-restart stress test :
1. Turn on the gmac forwarding when mkt_open is only halfway initialized
or start deinit in mtk_close without forbid forwarding in gmac, this
can lead to unknown exceptions.
2. Update the init/deinit order in mtk_open/mtk_close.
3. Move the configure of gdm from mtk_mac_config to mtk_hw_init, avoid
asynchronous operations on gdm config.
4. Update related patches.
[Release-log]
N/A
Change-Id: I80f594948b0c0ddc7eb34bb47e78e2ff74229f6a
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/6728789
Fix the conditions for binding VLAN to HNAT.
Whether egress packets carries vlan depends on skb ->vlan_present.
The previous code will fail when encountering the following situation:
PC1->eth1.45-->lan-->PC2.
PC1 send packets with vlan 45,
disable HNAT, PC2 capture packets without vlan.
enable HNAT, PC2 capture packets with vlan.
This patch fix it.
[Release-log]
N/A
Change-Id: Iaa0916680733eda810b37abea2d0bd7201932cfd
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/6879837
Fix the problem that deleting wifi subinterface fails.
Fix duplication of adding the same subinterface to whnat_interface.
The previous code will fail when encountering the following situations:
1:Add subinterface to whnat_interface and then delete it,
finally, delete the subinterface failed.
2:Add wifi subinterface(eg:rax0.200) to whnat_interface, then rax0 down,
add the same wifi subinterface to whnat_interface through echo command.
there are two identical wifi subinrefaces in whnat_interface.
The patch fix these.
[Release-log]
N/A
Change-Id: I6ae98fbfc12522cfd6528df81509e5bc30a87e76
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/6873054
[Description]
Add processing of uninitialized mac header skb in HNAT to avoid crash.
[Release-log]
N/A
Change-Id: I7915ab5cb9c366728b70a6597ba06cb6f984e4a8
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/6887447
On some of the hardware revisions of Asus RT-AC88U, brcmfmac detects the
4366b1 wireless chip and tries to load the firmware file which doesn't
exist because it's not included in the image.
Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 2b9bb5b187022f8b64c84781c071d6c2b0ce3e45)
The image builds and works fine on Asus RT-AC88U. Therefore, remove the
BROKEN flag from the makefile.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 5c1b1918abf853c95976daf7fea58fb1355eae6d)
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.
Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit f4e219fd5e6cfa33d234dad134fb105cc1620f54)
Asus RT-AC88U is an AC3100 router featuring 9 Ethernet ports over the
integrated Broadcom and the external Realtek switch.
Hardware info:
* Processor: Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
* Switch: BCM53012 in BCM4709C0KFEBG & external RTL8365MB
* DDR3 RAM: 512 MB
* Flash: 128 MB (ESMT F59L1G81LA-25T)
* 2.4GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* 5GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* Ports: 8 Ports, 1 WAN Ports
Flashing instructions:
* Boot to CFE Recovery Mode by holding the reset button while power-on.
* Connect to the router with an ethernet cable.
* Set IPv4 address of the computer to 192.168.1.2 subnet 255.255.255.0.
* Head to http://192.168.1.1.
* Reset NVRAM.
* Upload the OpenWrt image.
CFE bootloader may reject flashing the image due to image integrity check.
In that case, follow the instructions below.
* Rename the OpenWrt image as firmware.trx.
* Run a TFTP server and make it serve the firmware.trx file.
* Run the URL below on a browser or curl.
http://192.168.1.1/do.htm?cmd=flash+-noheader+192.168.1.2:firmware.trx+flash0.trx
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
[rmilecki: mark BROKEN until we sort out nvram & CFE recovery]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 72b9b721d707b7f70109eb70b2a9f22449ceba08)
When we use the internal toolchain USE_SSTRIP will be selected by
default for musl libc and USE_STRIP when glibc is used. Do the same when
an external toolchain is used. USE_GLIBC will also be set for external
toolchain builds based on the EXTERNAL_TOOLCHAIN_LIBC_USE_GLIBC setting.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9403810c020cca136149973a3929bf77a1f501aa)
Expose the SDK options for binary stripping to the menuconfig. This
way, packages can easily be built with debug symbols using the SDK.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit bb817bb4b8b0b546a70e45bd907ebfeea2370dcd)
Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).
Backport upstream commit for its effect on the number of connections per
hashtable bucket.
Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit 15fbb916669dcdfcc706e9e75263ab63f9f27c00)
Add missing define for dwc quirk patch required to fix compilation error
for layerscape target. This was wrongly dropped in a kernel bump.
Fixes: 8e5de897691a ("kernel: bump 5.4 to 5.4.213")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This fixes:
[ 10.440495] bcm_ns_usb2 1800c000.usb2-phy: can't request region for resource [mem 0x1800c000-0x1800cfff]
[ 10.450039] bcm_ns_usb2 1800c000.usb2-phy: Failed to map DMU regs
[ 10.456183] bcm_ns_usb2: probe of 1800c000.usb2-phy failed with error -16
caused by conflict in allocating resources.
Fixes: 44ce70f0e209c ("bcm53xx: drop downstream patch that now breaks pinctrl driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1d7c1a41987ae463700224c08a3629e4086a8f39)
This includes:
1. BCM5301X changes from 5.14 and queued 5.15 stuff
2. NSP changes from 5.11 - 5.15 for kernel 5.10
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit bce00f47e5d67e5a33e9d7fa137cbe0a5d3d334b)
Fix Intel X550 IOT issue.
Due to X550 doesn't advertise 2.5G/5G link capability, phlylink
cannot resolve link speed/duplex in the phy_resolve_aneg_linkmode().
Therefore, we handle the link speed from vendor registers.
If without this patch, phylink will show unknown speed messages
when link with NBASE-T link partner.
[Release-log]
N/A
Change-Id: Iaef49fe8ea6ef7c6dc022e50456903b7feb4eef6
Reviewed-on: https://gerrit.mediatek.inc/c/openwrt/feeds/mtk_openwrt_feeds/+/6852800
The most affecting change is move of files from bcm4908/ to the bcmbca/.
That required updating few paths.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 45ac906c6415cebd12281088da6b06668c057f0a)
1. Include Linux DTB
2. Add 50991 variant (seems to differ by 1 PHY we don't support yet)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit b8f8c6f2dd8d47216117cb5b78184531ab21dddd)