diff --git a/defconfig/mt7981-ax3000.config b/defconfig/mt7981-ax3000.config index c60f6d7ac4..df50c6ed16 100644 --- a/defconfig/mt7981-ax3000.config +++ b/defconfig/mt7981-ax3000.config @@ -2,6 +2,7 @@ CONFIG_TARGET_mediatek=y CONFIG_TARGET_mediatek_mt7981=y CONFIG_TARGET_MULTI_PROFILE=y CONFIG_TARGET_DEVICE_mediatek_mt7981_DEVICE_cetron_ct3003=y +CONFIG_TARGET_DEVICE_mediatek_mt7981_DEVICE_cmcc_rax3000m=y CONFIG_TARGET_DEVICE_mediatek_mt7981_DEVICE_jcg_q30=y CONFIG_TARGET_DEVICE_mediatek_mt7981_DEVICE_livinet_zr-3020=y CONFIG_TARGET_DEVICE_mediatek_mt7981_DEVICE_mt7981-360-t7=y diff --git a/package/boot/uboot-envtools/files/mediatek b/package/boot/uboot-envtools/files/mediatek index 2b4a907439..8f84e1e89c 100644 --- a/package/boot/uboot-envtools/files/mediatek +++ b/package/boot/uboot-envtools/files/mediatek @@ -17,6 +17,9 @@ case "$board" in livinet,zr-3020*) ubootenv_add_uci_config "/dev/mtd2" "0x0" "0x20000" "0x20000" "1" ;; +cmcc,rax3000m) + ubootenv_add_uci_config "/dev/mtd2" "0x0" "0x80000" "0x20000" "4" + ;; xiaomi,mi-router-wr30u* |\ xiaomi,redmi-router-ax6000*) ubootenv_add_uci_config "/dev/mtd2" "0x0" "0x10000" "0x20000" "1" diff --git a/target/linux/mediatek/base-files/sbin/smp.sh b/target/linux/mediatek/base-files/sbin/smp.sh index 38d630ecd2..cf02de632f 100755 --- a/target/linux/mediatek/base-files/sbin/smp.sh +++ b/target/linux/mediatek/base-files/sbin/smp.sh @@ -720,6 +720,7 @@ setup_model() *zr-3020* |\ *360,t7* |\ xiaomi,mi-router-wr30u* |\ + *rax3000m* |\ *7981*) MT7981_whnat $num_of_wifi ;; diff --git a/target/linux/mediatek/files-5.4/arch/arm64/boot/dts/mediatek/mt7981-cmcc-rax3000m.dts b/target/linux/mediatek/files-5.4/arch/arm64/boot/dts/mediatek/mt7981-cmcc-rax3000m.dts new file mode 100644 index 0000000000..dd0faeb61e --- /dev/null +++ b/target/linux/mediatek/files-5.4/arch/arm64/boot/dts/mediatek/mt7981-cmcc-rax3000m.dts @@ -0,0 +1,223 @@ +/dts-v1/; +#include "mt7981.dtsi" + +/ { + model = "CMCC RAX3000M"; + compatible = "cmcc,rax3000m", "mediatek,mt7981"; + + aliases { + led-boot = &red_led; + led-failsafe = &red_led; + led-running = &green_led; + led-upgrade = &blue_led; + }; + + chosen { + bootargs = "console=ttyS0,115200n1 loglevel=8 \ + earlycon=uart8250,mmio32,0x11002000"; + }; + + memory { + reg = <0 0x40000000 0 0x20000000>; + }; + + leds { + compatible = "gpio-leds"; + + red_led: red { + label = "rax3000m:red"; + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + }; + + green_led: green { + label = "rax3000m:green"; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + blue_led: blue { + label = "rax3000m:blue"; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + + mesh { + label = "wps"; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + }; + }; + + gsw: gsw@0 { + compatible = "mediatek,mt753x"; + mediatek,ethsys = <ðsys>; + #address-cells = <1>; + #size-cells = <0>; + }; + + nmbm_spim_nand { + compatible = "generic,nmbm"; + #address-cells = <1>; + #size-cells = <1>; + + lower-mtd-device = <&spi_nand>; + forced-create; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x0 0x100000>; + read-only; + }; + partition@100000 { + label = "u-boot-env"; + reg = <0x100000 0x80000>; + }; + partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + }; + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + }; + partition@580000 { + label = "ubi"; + reg = <0x580000 0x7200000>; + }; // ubi+plugins+fwk+fwk2 + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&phy0>; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-id03a2.9461"; + reg = <0>; + phy-mode = "gmii"; + nvmem-cells = <&phy_calibration>; + nvmem-cell-names = "phy-cal-data"; + }; + }; +}; + +&gsw { + mediatek,mdio = <&mdio>; + mediatek,mdio_master_pinmux = <0>; + reset-gpios = <&pio 39 0>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + status = "okay"; + + port6: port@6 { + compatible = "mediatek,mt753x-port"; + //mediatek,ssc-on; + reg = <6>; + phy-mode = "sgmii"; + + fixed-link { + speed = <2500>; + full-duplex; + }; + }; +}; + +&hnat { + mtketh-wan = "eth1"; + mtketh-lan = "eth0"; + mtketh-max-gmac = <2>; + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: spi_nand@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <52000000>; + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>; /* 'SPINAND' */ + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = ; + bias-pull-up = ; + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = ; + bias-pull-down = ; + }; + }; +}; + +&xhci { + mediatek,u3p-dis-msk = <0x0>; + phys = <&u2port0 PHY_TYPE_USB2>, + <&u3port0 PHY_TYPE_USB3>; + status = "okay"; +}; diff --git a/target/linux/mediatek/image/mt7981.mk b/target/linux/mediatek/image/mt7981.mk index 647f1e7618..7bb5b23eeb 100644 --- a/target/linux/mediatek/image/mt7981.mk +++ b/target/linux/mediatek/image/mt7981.mk @@ -335,3 +335,23 @@ define Device/livinet_zr-3020 IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata endef TARGET_DEVICES += livinet_zr-3020 + +define Device/cmcc_rax3000m + DEVICE_VENDOR := CMCC + DEVICE_MODEL := RAX3000M + DEVICE_DTS := mt7981-cmcc-rax3000m + DEVICE_DTS_DIR := $(DTS_DIR)/mediatek + DEVICE_PACKAGES := mkf2fs e2fsprogs blkid blockdev losetup kmod-usb-printer \ + kmod-fs-ext4 kmod-fs-exfat kmod-fs-ksmbd kmod-fs-ntfs3 \ + kmod-fs-vfat kmod-nls-cp437 kmod-nls-iso8859-1 + SUPPORTED_DEVICES := cmcc,rax3000m + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 116736k + KERNEL_IN_UBI := 1 + IMAGES += factory.bin + IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE) + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += cmcc_rax3000m diff --git a/target/linux/mediatek/mt7981/base-files/etc/board.d/02_network b/target/linux/mediatek/mt7981/base-files/etc/board.d/02_network index 3e58884fed..eacb75e4d7 100755 --- a/target/linux/mediatek/mt7981/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/mt7981/base-files/etc/board.d/02_network @@ -42,6 +42,11 @@ mediatek_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "0:wan" "6t@eth0" ;; + *rax3000m*) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ucidef_add_switch "switch0" \ + "0:lan" "1:lan" "2:lan" "6u@eth0" + ;; *mt3000* |\ glinet,x3000-emmc |\ *xe3000* |\ diff --git a/target/linux/mediatek/mt7981/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/mt7981/base-files/lib/upgrade/platform.sh index b49ec53e82..92245c577b 100644 --- a/target/linux/mediatek/mt7981/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/mt7981/base-files/lib/upgrade/platform.sh @@ -195,6 +195,7 @@ platform_do_upgrade() { *360,t7* |\ *cetron,ct3003* |\ *jcg,q30* |\ + cmcc,rax3000m |\ *snand*) nand_do_upgrade "$1" ;; @@ -229,6 +230,7 @@ platform_check_image() { xiaomi,mi-router-wr30u-112m|\ *cetron,ct3003* |\ *jcg,q30* |\ + cmcc,rax3000m |\ *snand* |\ *emmc*) # tar magic `ustar`