mirror of
https://github.com/hanwckf/immortalwrt-mt798x.git
synced 2025-01-08 10:23:47 +08:00
ath79: add support for TP-Link CPE510-v2/v3
TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, and 4 green LEDs - 1 10/100Mbps Shielded Ethernet Port (Passive PoE in) - Built-in 13dBi 2x2 dual-polarized directional MIMO antenna - Adjustable transmission power from 0 to 23dBm/200mw Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [whitespace fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit is contained in:
Andrew Cameron
Petr Štetiar
parent
8e384ba830
commit
cad4132e00
@ -158,6 +158,15 @@ tplink,cpe210-v3)
|
||||
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "tp-link:green:link3" "wlan0" "60" "100"
|
||||
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "tp-link:green:link4" "wlan0" "80" "100"
|
||||
;;
|
||||
tplink,cpe510-v2|\
|
||||
tplink,cpe510-v3)
|
||||
ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0"
|
||||
ucidef_set_rssimon "wlan0" "200000" "1"
|
||||
ucidef_set_led_rssi "rssilow" "RSSILOW" "tp-link:green:link1" "wlan0" "1" "100" "0" "13"
|
||||
ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "tp-link:green:link2" "wlan0" "26" "100" "-25" "13"
|
||||
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "tp-link:green:link3" "wlan0" "51" "100" "-50" "13"
|
||||
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "tp-link:green:link4" "wlan0" "76" "100" "-75" "13"
|
||||
;;
|
||||
tplink,cpe610-v1)
|
||||
ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0"
|
||||
;;
|
||||
|
||||
@ -28,6 +28,8 @@ ath79_setup_interfaces()
|
||||
pqi,air-pen|\
|
||||
tplink,cpe210-v2|\
|
||||
tplink,cpe210-v3|\
|
||||
tplink,cpe510-v2|\
|
||||
tplink,cpe510-v3|\
|
||||
tplink,cpe610-v1|\
|
||||
tplink,re350k-v1|\
|
||||
tplink,re355-v1|\
|
||||
|
||||
9
target/linux/ath79/dts/ar9344_tplink_cpe510-v2.dts
Normal file
9
target/linux/ath79/dts/ar9344_tplink_cpe510-v2.dts
Normal file
@ -0,0 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "ar9344_tplink_cpe510.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "tplink,cpe510-v2", "qca,ar9344";
|
||||
model = "TP-Link CPE510 v2";
|
||||
};
|
||||
9
target/linux/ath79/dts/ar9344_tplink_cpe510-v3.dts
Normal file
9
target/linux/ath79/dts/ar9344_tplink_cpe510-v3.dts
Normal file
@ -0,0 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "ar9344_tplink_cpe510.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "tplink,cpe510-v3", "qca,ar9344";
|
||||
model = "TP-Link CPE510 v3";
|
||||
};
|
||||
152
target/linux/ath79/dts/ar9344_tplink_cpe510.dtsi
Normal file
152
target/linux/ath79/dts/ar9344_tplink_cpe510.dtsi
Normal file
@ -0,0 +1,152 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar9344.dtsi"
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
led-boot = &system;
|
||||
led-failsafe = &system;
|
||||
led-running = &system;
|
||||
led-upgrade = &system;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
lan {
|
||||
label = "tp-link:green:lan";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
link1 {
|
||||
label = "tp-link:green:link1";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
link2 {
|
||||
label = "tp-link:green:link2";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
link3 {
|
||||
label = "tp-link:green:link3";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
system: link4 {
|
||||
label = "tp-link:green:link4";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&ref {
|
||||
clock-frequency = <40000000>;
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
num-cs = <1>;
|
||||
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
uboot: partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "partition-table";
|
||||
reg = <0x020000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
info: partition@30000 {
|
||||
label = "info";
|
||||
reg = <0x030000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "firmware";
|
||||
reg = <0x040000 0x780000>;
|
||||
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "kernel";
|
||||
reg = <0x000000 0x200000>;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "rootfs";
|
||||
reg = <0x200000 0x580000>;
|
||||
};
|
||||
};
|
||||
|
||||
partition@7c0000 {
|
||||
label = "config";
|
||||
reg = <0x7c0000 0x030000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@7f0000 {
|
||||
label = "art";
|
||||
reg = <0x7f0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&info 0x08>;
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&info 0x08>;
|
||||
|
||||
phy-mode = "mii";
|
||||
phy-handle = <&swphy4>;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
compatible = "syscon", "simple-mfd";
|
||||
};
|
||||
@ -159,6 +159,40 @@ define Device/tplink_cpe210-v3
|
||||
endef
|
||||
TARGET_DEVICES += tplink_cpe210-v3
|
||||
|
||||
define Device/tplink_cpe510-v2
|
||||
$(Device/tplink-safeloader)
|
||||
ATH_SOC := ar9344
|
||||
IMAGE_SIZE := 7680k
|
||||
DEVICE_MODEL := CPE510
|
||||
DEVICE_VARIANT := v2
|
||||
DEVICE_PACKAGES := rssileds
|
||||
TPLINK_BOARD_ID := CPE510V2
|
||||
LOADER_TYPE := elf
|
||||
LOADER_FLASH_OFFS := 0x43000
|
||||
COMPILE := loader-$(1).elf
|
||||
COMPILE/loader-$(1).elf := loader-okli-compile
|
||||
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 12288
|
||||
SUPPORTED_DEVICES += cpe510-v2
|
||||
endef
|
||||
TARGET_DEVICES += tplink_cpe510-v2
|
||||
|
||||
define Device/tplink_cpe510-v3
|
||||
$(Device/tplink-safeloader)
|
||||
ATH_SOC := ar9344
|
||||
IMAGE_SIZE := 7680k
|
||||
DEVICE_MODEL := CPE510
|
||||
DEVICE_VARIANT := v3
|
||||
DEVICE_PACKAGES := rssileds
|
||||
TPLINK_BOARD_ID := CPE510V3
|
||||
LOADER_TYPE := elf
|
||||
LOADER_FLASH_OFFS := 0x43000
|
||||
COMPILE := loader-$(1).elf
|
||||
COMPILE/loader-$(1).elf := loader-okli-compile
|
||||
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 12288
|
||||
SUPPORTED_DEVICES += cpe510-v3
|
||||
endef
|
||||
TARGET_DEVICES += tplink_cpe510-v3
|
||||
|
||||
define Device/tplink_cpe610-v1
|
||||
$(Device/tplink-safeloader)
|
||||
ATH_SOC := ar9344
|
||||
|
||||
@ -278,6 +278,91 @@ static struct device_info boards[] = {
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "support-list",
|
||||
},
|
||||
|
||||
/** Firmware layout for the CPE510 V2 */
|
||||
{
|
||||
.id = "CPE510V2",
|
||||
.vendor = "CPE510(TP-LINK|UN|N300-5):2.0\r\n",
|
||||
.support_list =
|
||||
"SupportList:\r\n"
|
||||
"CPE510(TP-LINK|EU|N300-5|00000000):2.0\r\n"
|
||||
"CPE510(TP-LINK|EU|N300-5|45550000):2.0\r\n"
|
||||
"CPE510(TP-LINK|EU|N300-5|55530000):2.0\r\n"
|
||||
"CPE510(TP-LINK|UN|N300-5|00000000):2.0\r\n"
|
||||
"CPE510(TP-LINK|UN|N300-5|45550000):2.0\r\n"
|
||||
"CPE510(TP-LINK|UN|N300-5|55530000):2.0\r\n"
|
||||
"CPE510(TP-LINK|US|N300-5|00000000):2.0\r\n"
|
||||
"CPE510(TP-LINK|US|N300-5|45550000):2.0\r\n"
|
||||
"CPE510(TP-LINK|US|N300-5|55530000):2.0\r\n"
|
||||
"CPE510(TP-LINK|UN|N300-5):2.0\r\n"
|
||||
"CPE510(TP-LINK|EU|N300-5):2.0\r\n"
|
||||
"CPE510(TP-LINK|US|N300-5):2.0\r\n",
|
||||
.support_trail = '\xff',
|
||||
.soft_ver = NULL,
|
||||
|
||||
.partitions = {
|
||||
{"fs-uboot", 0x00000, 0x20000},
|
||||
{"partition-table", 0x20000, 0x02000},
|
||||
{"default-mac", 0x30000, 0x00020},
|
||||
{"product-info", 0x31100, 0x00100},
|
||||
{"signature", 0x32000, 0x00400},
|
||||
{"os-image", 0x40000, 0x200000},
|
||||
{"file-system", 0x240000, 0x570000},
|
||||
{"soft-version", 0x7b0000, 0x00100},
|
||||
{"support-list", 0x7b1000, 0x00400},
|
||||
{"user-config", 0x7c0000, 0x10000},
|
||||
{"default-config", 0x7d0000, 0x10000},
|
||||
{"log", 0x7e0000, 0x10000},
|
||||
{"radio", 0x7f0000, 0x10000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "support-list",
|
||||
},
|
||||
|
||||
/** Firmware layout for the CPE510 V3 */
|
||||
{
|
||||
.id = "CPE510V3",
|
||||
.vendor = "CPE510(TP-LINK|UN|N300-5):3.0\r\n",
|
||||
.support_list =
|
||||
"SupportList:\r\n"
|
||||
"CPE510(TP-LINK|EU|N300-5|00000000):3.0\r\n"
|
||||
"CPE510(TP-LINK|EU|N300-5|45550000):3.0\r\n"
|
||||
"CPE510(TP-LINK|EU|N300-5|55530000):3.0\r\n"
|
||||
"CPE510(TP-LINK|UN|N300-5|00000000):3.0\r\n"
|
||||
"CPE510(TP-LINK|UN|N300-5|45550000):3.0\r\n"
|
||||
"CPE510(TP-LINK|UN|N300-5|55530000):3.0\r\n"
|
||||
"CPE510(TP-LINK|US|N300-5|00000000):3.0\r\n"
|
||||
"CPE510(TP-LINK|US|N300-5|45550000):3.0\r\n"
|
||||
"CPE510(TP-LINK|US|N300-5|55530000):3.0\r\n"
|
||||
"CPE510(TP-LINK|UN|N300-5):3.0\r\n"
|
||||
"CPE510(TP-LINK|EU|N300-5):3.0\r\n"
|
||||
"CPE510(TP-LINK|US|N300-5):3.0\r\n",
|
||||
.support_trail = '\xff',
|
||||
.soft_ver = NULL,
|
||||
|
||||
.partitions = {
|
||||
{"fs-uboot", 0x00000, 0x20000},
|
||||
{"partition-table", 0x20000, 0x02000},
|
||||
{"default-mac", 0x30000, 0x00020},
|
||||
{"product-info", 0x31100, 0x00100},
|
||||
{"signature", 0x32000, 0x00400},
|
||||
{"os-image", 0x40000, 0x200000},
|
||||
{"file-system", 0x240000, 0x570000},
|
||||
{"soft-version", 0x7b0000, 0x00100},
|
||||
{"support-list", 0x7b1000, 0x00400},
|
||||
{"user-config", 0x7c0000, 0x10000},
|
||||
{"default-config", 0x7d0000, 0x10000},
|
||||
{"log", 0x7e0000, 0x10000},
|
||||
{"radio", 0x7f0000, 0x10000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "support-list",
|
||||
},
|
||||
|
||||
/** Firmware layout for the CPE610V1 */
|
||||
{
|
||||
.id = "CPE610V1",
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user