mirror of
https://github.com/hanwckf/immortalwrt-mt798x.git
synced 2025-01-09 02:43:53 +08:00
ipq40xx: ipq4019: Add new device Compex WPJ419
This device contains 2 flash devices. One NOR (32M) and one NAND (128M).
U-boot and caldata are on the NOR, the firmware on the NAND.
SoC: IPQ4019
CPU: 4x 710MHz ARMv7
RAM: 256MB
FLASH: NOR:32MB NAND:128MB
ETH: 2x GMAC Gigabit
POE: 802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V)
WIFI: 1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO
1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO
USB: 1x 3.0
PCI: 1x Mini PCIe
SIM: 1x Slot
SD: 1x MicroSD slot
BTN: Reset
LED: - Power
- Ethernet
UART: 1x Serial Port 4 Pin Connector (UART)
1x Serial Port 6 Pin Connector (High Speed UART)
POWER: 12V 2A
Installation
------------
Initial flashing can only be done via u-boot using the following commands:
tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi
nand erase.chip; nand write ${fileaddr} 0x0 ${filesize}
res
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
This commit is contained in:
Daniel Danzberger
John Crispin
parent
2d00cf7515
commit
affe633be4
@ -48,6 +48,7 @@ ipq40xx_setup_interfaces()
|
||||
ucidef_set_interface_lan "eth0"
|
||||
;;
|
||||
avm,fritzrepeater-3000|\
|
||||
compex,wpj419|\
|
||||
compex,wpj428)
|
||||
ucidef_set_interface_lan "eth0 eth1"
|
||||
;;
|
||||
|
||||
@ -70,6 +70,7 @@ case "$FIRMWARE" in
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
|
||||
;;
|
||||
compex,wpj419 |\
|
||||
compex,wpj428 |\
|
||||
engenius,eap1300 |\
|
||||
openmesh,a42 |\
|
||||
@ -133,6 +134,7 @@ case "$FIRMWARE" in
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
|
||||
;;
|
||||
compex,wpj419 |\
|
||||
compex,wpj428 |\
|
||||
engenius,eap1300 |\
|
||||
openmesh,a42 |\
|
||||
|
||||
@ -73,6 +73,9 @@ platform_do_upgrade() {
|
||||
CI_KERNPART="linux"
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
compex,wpj419)
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
linksys,ea6350v3 |\
|
||||
linksys,ea8300)
|
||||
platform_do_upgrade_linksys "$1"
|
||||
|
||||
@ -0,0 +1,374 @@
|
||||
/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
|
||||
* Copyright (c) 2019, Nguyen Dinh Phi <phi_nguyen@compex.com.sg>
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
|
||||
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
|
||||
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
|
||||
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
|
||||
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
|
||||
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
|
||||
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Compex WPJ419";
|
||||
compatible = "compex,wpj419", "qcom,ipq4019";
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x10000000>;
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
ranges;
|
||||
rsvd1@87000000 {
|
||||
/* Reserved for other subsystem */
|
||||
reg = <0x87000000 0x500000>;
|
||||
no-map;
|
||||
};
|
||||
wifi_dump@87500000 {
|
||||
reg = <0x87500000 0x600000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
rsvd2@87B00000 {
|
||||
/* Reserved for other subsystem */
|
||||
reg = <0x87B00000 0x500000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1 clk_ignore_unused";
|
||||
};
|
||||
|
||||
soc {
|
||||
pinctrl@1000000 {
|
||||
mdio_pins: mdio_pinmux {
|
||||
mux_1 {
|
||||
pins = "gpio6";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mux_2 {
|
||||
pins = "gpio7";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_0_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
serial_1_pins: serial1_pinmux {
|
||||
mux {
|
||||
pins = "gpio8", "gpio9", "gpio10", "gpio11";
|
||||
function = "blsp_uart1";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pinmux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio13", "gpio14", "gpio15";
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
pinmux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio12";
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
i2c_0_pins: i2c_0_pinmux {
|
||||
mux {
|
||||
pins = "gpio20", "gpio21";
|
||||
function = "blsp_i2c0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
nand_pins: nand_pins {
|
||||
pullups {
|
||||
pins = "gpio52", "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio54", "gpio55", "gpio56",
|
||||
"gpio57", "gpio60", "gpio61",
|
||||
"gpio62", "gpio63", "gpio64",
|
||||
"gpio65", "gpio66", "gpio67",
|
||||
"gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
led_0_pins: led0_pinmux {
|
||||
mux_1 {
|
||||
pins = "gpio36";
|
||||
function = "led0";
|
||||
bias-pull-down;
|
||||
};
|
||||
mux_2 {
|
||||
pins = "gpio40";
|
||||
function = "led4";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
blsp_dma: dma@7884000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
spi_0: spi@78b5000 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, <&tlmm 41 GPIO_ACTIVE_HIGH>;
|
||||
num-cs = <2>;
|
||||
|
||||
flash0@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <24000000>;
|
||||
broken-flash-reset;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x040000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x060000 0x060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0x0c0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0x0d0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@e0000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x0e0000 0x010000>;
|
||||
};
|
||||
|
||||
partition@f0000 {
|
||||
label = "u-boot";
|
||||
reg = <0x0f0000 0x080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x170000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
nand@1 {
|
||||
reg = <1>;
|
||||
status = "okay";
|
||||
compatible = "spi-nand";
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
/* The device has 128MB, but we can only address
|
||||
* 64MB because of the bootloader's default settings.
|
||||
* This is due to the old mt29f driver,
|
||||
* which detected the deivce with only 64MB
|
||||
*/
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0x0000000 0x4000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
phy-reset-gpio = <&tlmm 47 0>;
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
i2c_0: i2c@78b7000 {
|
||||
pinctrl-0 = <&i2c_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
serial@78af000 {
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
serial@78b0000 {
|
||||
pinctrl-0 = <&serial_1_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb3_ss_phy: ssphy@9a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb3_hs_phy: hsphy@a6000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb3: usb3@8af8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb2_hs_phy: hsphy@a8000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb2: usb2@60f8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
cryptobam: dma@8e04000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
switch_lan_bmp = <0x1e>;
|
||||
switch_wan_bmp = <0x20>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
qpic_bam: dma@7984000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
pcie0: pci@40000000 {
|
||||
status = "okay";
|
||||
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
nand: qpic-nand@79b0000 {
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
qcom,phy_mdio_addr = <4>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <2 0x20>;
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
qcom,phy_mdio_addr = <3>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <1 0x10>;
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
};
|
||||
@ -164,6 +164,20 @@ define Device/avm_fritzrepeater-3000
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzrepeater-3000
|
||||
|
||||
define Device/compex_wpj419
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Compex
|
||||
DEVICE_MODEL := WPJ419
|
||||
DEVICE_DTS := qcom-ipq4019-wpj419
|
||||
DEVICE_DTS_CONFIG := config@12
|
||||
KERNEL_INSTALL := 1
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
FILESYSTEMS := squashfs
|
||||
endef
|
||||
TARGET_DEVICES += compex_wpj419
|
||||
|
||||
define Device/compex_wpj428
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Compex
|
||||
|
||||
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -785,11 +785,35 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -785,11 +785,36 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -40,6 +40,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
|
||||
+ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
|
||||
+ qcom-ipq4019-unielec-u4019-32m.dtb \
|
||||
+ qcom-ipq4019-wpj419.dtb \
|
||||
+ qcom-ipq4028-wpj428.dtb \
|
||||
+ qcom-ipq4029-gl-b1300.dtb \
|
||||
+ qcom-ipq4029-mr33.dtb \
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user