mirror of
https://github.com/hanwckf/immortalwrt-mt798x.git
synced 2025-01-07 01:53:34 +08:00
mediatek: add support for Routerich AX3000 (#303)
* mediatek: add support for Routerich AX3000
Routerich AX3000 is a wireless WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : DDR3 256 MiB (ESMT M15T2G16128A)
- Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
- USB : 1x 2.0
- UART : through-hole on PCB
- [J500] GND, TX, RX, 3.3V (115200n8)
- Buttons : Mesh, Reset
- LEDs : 1x Power (Blue)
1x WiFi 2.4 GHz (Blue)
1x WiFi 5 GHz (Red)
1x Mesh (Blue)
3x LAN activity (Blue)
1x WAN activity (Blue)
2x WAN no-internet (Red)
- Power : 12 VDC, 1.5 A
Installation
------------
Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface
(without keeping settings).
Return to stock
---------------
Install stock firmware image (without keeping settings) using OpenWrt
sysupgrade method.
Recovery
--------
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 24:0f:5e:xx:xx:b4 | label |
| LAN | 24:0f:5e:xx:xx:b5 | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3 |
+---------+-------------------+-----------+
The WLAN 2g MAC was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
---------
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Co-authored-by: hanwckf <hanwckf@vip.qq.com>
Co-authored-by: hanwckf <my375229675@gmail.com>
This commit is contained in:
csharper2005
GitHub
parent
7a0b5b83c2
commit
90ac94fb7a
@ -31,6 +31,8 @@ CONFIG_TARGET_DEVICE_mediatek_mt7981_DEVICE_mt7981-clt-r30b1=y
|
||||
CONFIG_TARGET_DEVICE_PACKAGES_mediatek_mt7981_DEVICE_mt7981-clt-r30b1=""
|
||||
CONFIG_TARGET_DEVICE_mediatek_mt7981_DEVICE_mt7981-clt-r30b1-112M=y
|
||||
CONFIG_TARGET_DEVICE_PACKAGES_mediatek_mt7981_DEVICE_mt7981-clt-r30b1-112M=""
|
||||
CONFIG_TARGET_DEVICE_mediatek_mt7981_DEVICE_routerich_ax3000=y
|
||||
CONFIG_TARGET_DEVICE_PACKAGES_mediatek_mt7981_DEVICE_routerich_ax3000=""
|
||||
CONFIG_TARGET_DEVICE_mediatek_mt7981_DEVICE_xiaomi_mi-router-ax3000t=y
|
||||
CONFIG_TARGET_DEVICE_PACKAGES_mediatek_mt7981_DEVICE_xiaomi_mi-router-ax3000t=""
|
||||
CONFIG_TARGET_DEVICE_mediatek_mt7981_DEVICE_xiaomi_mi-router-ax3000t-stock=y
|
||||
|
||||
@ -0,0 +1,294 @@
|
||||
/dts-v1/;
|
||||
#include "mt7981.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Routerich AX3000";
|
||||
compatible = "routerich,ax3000", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_blue;
|
||||
led-failsafe = &led_power_blue;
|
||||
led-running = &led_power_blue;
|
||||
led-upgrade = &led_power_blue;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n1 loglevel=8 \
|
||||
earlycon=uart8250,mmio32,0x11002000";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000 0 0x10000000>;
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-0 {
|
||||
label = "red:wlan5g";
|
||||
gpios = <&pio 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-1 {
|
||||
label = "red:wan";
|
||||
gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_power_blue: led-2 {
|
||||
label = "blue:power";
|
||||
gpios = <&pio 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-3 {
|
||||
label = "blue:lan1";
|
||||
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-4 {
|
||||
label = "blue:lan2";
|
||||
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-5 {
|
||||
label = "blue:lan3";
|
||||
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-6 {
|
||||
label = "blue:wan";
|
||||
gpios = <&pio 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-7 {
|
||||
label = "blue:wlan2g";
|
||||
gpios = <&pio 34 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-8 {
|
||||
label = "blue:mesh";
|
||||
gpios = <&pio 35 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-mesh {
|
||||
label = "mesh";
|
||||
linux,code = <BTN_0>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button-reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gsw: gsw@0 {
|
||||
compatible = "mediatek,mt753x";
|
||||
mediatek,ethsys = <ðsys>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
nmbm_spim_nand {
|
||||
compatible = "generic,nmbm";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
lower-mtd-device = <&spi_nand>;
|
||||
forced-create;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0_all {
|
||||
label = "spi0.0";
|
||||
reg = <0x0 0x8000000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x0 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x100000 0x80000>;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x580000 0x4000000>;
|
||||
};
|
||||
|
||||
partition@4580000 {
|
||||
label = "firmware_backup";
|
||||
reg = <0x4580000 0x2000000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6580000 {
|
||||
label = "zrsave";
|
||||
reg = <0x6580000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6680000 {
|
||||
label = "config2";
|
||||
reg = <0x6680000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
mdio: mdio-bus {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&gsw {
|
||||
mediatek,mdio = <&mdio>;
|
||||
mediatek,mdio_master_pinmux = <0>;
|
||||
reset-gpios = <&pio 39 0>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
||||
status = "okay";
|
||||
|
||||
port5: port@5 {
|
||||
compatible = "mediatek,mt753x-port";
|
||||
reg = <5>;
|
||||
phy-mode = "sgmii";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
port6: port@6 {
|
||||
compatible = "mediatek,mt753x-port";
|
||||
mediatek,ssc-on;
|
||||
reg = <6>;
|
||||
phy-mode = "sgmii";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&hnat {
|
||||
mtketh-wan = "eth1";
|
||||
mtketh-lan = "eth0";
|
||||
mtketh-max-gmac = <2>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand: spi_nand@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
|
||||
spi-cal-enable;
|
||||
spi-cal-mode = "read-data";
|
||||
spi-cal-datalen = <7>;
|
||||
spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
|
||||
spi-cal-addrlen = <5>;
|
||||
spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&xhci {
|
||||
mediatek,u3p-dis-msk = <0x0>;
|
||||
status = "okay";
|
||||
};
|
||||
@ -683,3 +683,19 @@ define Device/nradio_wt9103_512m
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += nradio_wt9103_512m
|
||||
|
||||
define Device/routerich_ax3000
|
||||
DEVICE_VENDOR := Routerich
|
||||
DEVICE_MODEL := AX3000
|
||||
DEVICE_DTS := mt7981-routerich-ax3000
|
||||
DEVICE_DTS_DIR := $(DTS_DIR)/mediatek
|
||||
SUPPORTED_DEVICES := routerich,ax3000 mediatek,mt7981-spim-snand-rfb
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 65536k
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
DEVICE_PACKAGES := $(MT7981_USB_PKGS)
|
||||
endef
|
||||
TARGET_DEVICES += routerich_ax3000
|
||||
|
||||
@ -57,6 +57,15 @@ nradio,wt9103)
|
||||
ucidef_set_led_netdev "5g" "5G" "hc:blue:cmode5" "eth1" "tx rx"
|
||||
ucidef_set_led_netdev "lan" "LAN" "hc:blue:cmode4" "br-lan" "tx rx"
|
||||
;;
|
||||
routerich,ax3000)
|
||||
ucidef_set_led_switch "lan1" "LAN1" "blue:lan1" "switch0" "0x01"
|
||||
ucidef_set_led_switch "lan2" "LAN2" "blue:lan2" "switch0" "0x04"
|
||||
ucidef_set_led_switch "lan3" "LAN3" "blue:lan3" "switch0" "0x08"
|
||||
ucidef_set_led_switch "wan" "WAN" "blue:wan" "switch0" "0x10"
|
||||
ucidef_set_led_switch "wan off" "WAN Off" "red:wan" "switch0" "0x10" "" "link"
|
||||
ucidef_set_led_netdev "wlan2g" "WLAN 2G" "blue:wlan2g" "ra0"
|
||||
ucidef_set_led_netdev "wlan5g" "WLAN 5G" "red:wlan5g" "rax0"
|
||||
;;
|
||||
esac
|
||||
|
||||
board_config_flush
|
||||
|
||||
@ -82,6 +82,11 @@ mediatek_setup_interfaces()
|
||||
nradio,wt9103)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1
|
||||
;;
|
||||
routerich,ax3000)
|
||||
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan:1" "2:lan:2" "3:lan:3" "4:wan" "6u@eth0" "5u@eth1"
|
||||
;;
|
||||
ikuai,q3000 |\
|
||||
ruijie,rg-x30e*)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan
|
||||
@ -242,10 +247,21 @@ mediatek_setup_macs()
|
||||
label_mac=$wan_mac
|
||||
local wifi_mac="$(mtd_get_mac_binary $part_name 0x04)"
|
||||
;;
|
||||
routerich,ax3000)
|
||||
local wifi_mac="$(mtd_get_mac_binary $part_name 0x4)"
|
||||
label_mac=$(macaddr_add $wifi_mac -2)
|
||||
lan_mac=$(macaddr_add $wifi_mac -1)
|
||||
wan_mac=$label_mac
|
||||
local b1dat="$(l1dat if2dat rax0)"
|
||||
if [ -f ${b1dat} ] && ! grep -q "MacAddress=" ${b1dat}; then
|
||||
local b1mac="$(macaddr_add $wifi_mac 1)"
|
||||
echo "MacAddress=$b1mac" >> ${b1dat}
|
||||
fi
|
||||
;;
|
||||
ikuai,q3000)
|
||||
wan_mac=$(mtd_get_mac_binary $part_name 0x10048)
|
||||
lan_mac=$(macaddr_add $wan_mac 1)
|
||||
;;
|
||||
;;
|
||||
ruijie,rg-x30e*)
|
||||
label_mac=$(mtd_get_mac_ascii product_info ethaddr)
|
||||
wan_mac=$label_mac
|
||||
|
||||
@ -206,6 +206,7 @@ platform_do_upgrade() {
|
||||
cmcc,rax3000m |\
|
||||
h3c,nx30pro |\
|
||||
*konka,komi-a31* |\
|
||||
routerich,ax3000 |\
|
||||
*nokia,ea0326gmp* |\
|
||||
*snand*)
|
||||
nand_do_upgrade "$1"
|
||||
@ -257,7 +258,8 @@ platform_check_image() {
|
||||
*nokia,ea0326gmp* |\
|
||||
nradio,wt9103 |\
|
||||
*snand* |\
|
||||
*emmc*)
|
||||
*emmc* |\
|
||||
routerich,ax3000)
|
||||
# tar magic `ustar`
|
||||
magic="$(dd if="$1" bs=1 skip=257 count=5 2>/dev/null)"
|
||||
|
||||
|
||||
@ -481,6 +481,7 @@ CONFIG_SPI_MT65XX=y
|
||||
CONFIG_SPI_MTK_SNFI=y
|
||||
CONFIG_SRCU=y
|
||||
CONFIG_SWCONFIG=y
|
||||
CONFIG_SWCONFIG_LEDS=y
|
||||
CONFIG_SWIOTLB=y
|
||||
CONFIG_SWPHY=y
|
||||
CONFIG_SYSCTL_EXCEPTION_TRACE=y
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user