mirror of
https://github.com/hanwckf/immortalwrt-mt798x.git
synced 2025-01-10 11:09:57 +08:00
ramips: add Netgear EX6150
SoC: MediaTek MT7621
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: MediaTek MT7662E bgn 2SS
WiFi: MediaTek MT7662E nac 2SS
BTN: ON/OFF - Reset - WPS - AP/Extender toggle
LED: - Arrow Right (blue)
- Arrow Left (blue)
- WiFi 1 (red/green)
- WiFi 2 (red/green)
- Power (green/amber)
- WPS (Green)
UART: UART is present as Pads on the backside of the PCB. They are
located on the other side of the Ethernet port.
3.3V - GND - TX - RX / 57600-8N1
3.3V is the nearest one to the antenna connectors
Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).
You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash
Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit is contained in:
David Bauer
Petr Štetiar
parent
58becdb30d
commit
3f019bf96c
@ -366,6 +366,7 @@ ramips_setup_interfaces()
|
||||
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5:wan" "6@eth0"
|
||||
;;
|
||||
dlink,dir-510l|\
|
||||
netgear,ex6150|\
|
||||
re350-v1)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "6@eth0"
|
||||
|
||||
247
target/linux/ramips/dts/EX6150.dts
Normal file
247
target/linux/ramips/dts/EX6150.dts
Normal file
@ -0,0 +1,247 @@
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "netgear,ex6150", "mediatek,mt7621-soc";
|
||||
model = "Netgear EX6150";
|
||||
|
||||
aliases {
|
||||
led-boot = &power_green;
|
||||
led-failsafe = &power_amber;
|
||||
led-running = &power_green;
|
||||
led-upgrade = &power_amber;
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x4000000>;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,57600";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power_amber: power_amber {
|
||||
label = "ex6150:amber:power";
|
||||
gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power_green: power_green {
|
||||
label = "ex6150:green:power";
|
||||
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "ex6150:green:wps";
|
||||
gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
rightarrow {
|
||||
label = "ex6150:blue:rightarrow";
|
||||
gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
leftarrow {
|
||||
label = "ex6150:blue:leftarrow";
|
||||
gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
router_green {
|
||||
label = "ex6150:green:router";
|
||||
gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
router_red {
|
||||
label = "ex6150:red:router";
|
||||
gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
client_green {
|
||||
label = "ex6150:green:client";
|
||||
gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
client_red {
|
||||
label = "ex6150:red:client";
|
||||
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
toggle {
|
||||
label = "AP/Extender toggle";
|
||||
gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
/* Active when switch is set to "Access Point" */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "config";
|
||||
reg = <0x30000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@40000 {
|
||||
label = "factory";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x50000 0xe80000>;
|
||||
};
|
||||
|
||||
partition@ed0000 {
|
||||
label = "ML1";
|
||||
reg = <0xed0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@ef0000 {
|
||||
label = "ML2";
|
||||
reg = <0xef0000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f10000 {
|
||||
label = "ML3";
|
||||
reg = <0xf10000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f30000 {
|
||||
label = "ML4";
|
||||
reg = <0xf30000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f50000 {
|
||||
label = "ML5";
|
||||
reg = <0xf50000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f70000 {
|
||||
label = "ML6";
|
||||
reg = <0xf70000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f90000 {
|
||||
label = "ML7";
|
||||
reg = <0xf90000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fb0000 {
|
||||
label = "T_Meter1";
|
||||
reg = <0xfb0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fc0000 {
|
||||
label = "T_Meter2";
|
||||
reg = <0xfc0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fd0000 {
|
||||
label = "POT";
|
||||
reg = <0xfd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fe0000 {
|
||||
label = "board_data";
|
||||
reg = <0xfe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@ff0000 {
|
||||
label = "nvram";
|
||||
reg = <0xff0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
wifi@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&factory 0x8000>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
wifi@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&factory 0x0000>;
|
||||
ieee80211-freq-limit = <2400000 2500000>;
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
mtd-mac-address = <&factory 0x00000004>;
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "sdhci", "rgmii2", "jtag";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -324,6 +324,17 @@ define Device/r6220
|
||||
endef
|
||||
TARGET_DEVICES += r6220
|
||||
|
||||
define Device/netgear_ex6150
|
||||
DTS := EX6150
|
||||
DEVICE_TITLE := Netgear EX6150
|
||||
DEVICE_PACKAGES := kmod-mt76x2 wpad-basic
|
||||
NETGEAR_BOARD_ID := U12H318T00_NETGEAR
|
||||
IMAGE_SIZE := 14848k
|
||||
IMAGES += factory.chk
|
||||
IMAGE/factory.chk := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | netgear-chk
|
||||
endef
|
||||
TARGET_DEVICES += netgear_ex6150
|
||||
|
||||
define Device/netgear_r6350
|
||||
DTS := R6350
|
||||
BLOCKSIZE := 128k
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user