Fix up commits

config/Config-build.in

@@ -100,7 +100,7 @@ menu "Global build settings"
 		bool "Include build configuration in firmware" if DEVEL
 		default n
 		help
-		  If enabled, config.buildinfo will be stored in /etc/build.config of firmware.
+		  If enabled, buildinfo files will be stored in /etc/build.* of firmware.
 
 	config COLLECT_KERNEL_DEBUG
 		bool

package/base-files/Makefile

@@ -198,7 +198,9 @@ define Package/base-files/install
 
 	$(if $(CONFIG_INCLUDE_CONFIG), \
 		echo -e "# Build configuration for board $(BOARD)/$(SUBTARGET)/$(PROFILE)\n" >$(1)/etc/build.config; \
-		cat $(BIN_DIR)/config.buildinfo >>$(1)/etc/build.config)
+		cat $(BIN_DIR)/config.buildinfo >>$(1)/etc/build.config; \
+		cat $(BIN_DIR)/feeds.buildinfo >>$(1)/etc/build.feeds; \
+		cat $(BIN_DIR)/version.buildinfo >>$(1)/etc/build.version)
 
 	$(if $(CONFIG_CLEAN_IPKG),, \
 		mkdir -p $(1)/etc/opkg; \

target/linux/ath79/dts/ar7161_buffalo_wzr-hp-ag300h.dts

@@ -234,14 +234,14 @@
 	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
-		spi-max-frequency = <104000000>;
+		spi-max-frequency = <50000000>;
 		m25p,fast-read;
 	};
 
 	flash1: flash@1 {
 		compatible = "jedec,spi-nor";
 		reg = <1>;
-		spi-max-frequency = <104000000>;
+		spi-max-frequency = <50000000>;
 		m25p,fast-read;
 	};
 };

target/linux/ath79/dts/ar9330_glinet_gl-ar150.dts

@@ -86,7 +86,7 @@
 
 	flash@0 {
 		compatible = "jedec,spi-nor";
-		spi-max-frequency = <104000000>;
+		spi-max-frequency = <50000000>;
 		reg = <0>;
 
 		partitions {

target/linux/ath79/dts/ar9330_pqi_air-pen.dts

@@ -75,7 +75,7 @@
 
 	flash@0 {
 		compatible = "jedec,spi-nor";
-		spi-max-frequency = <104000000>;
+		spi-max-frequency = <50000000>;
 		reg = <0>;
 
 		partitions {

target/linux/ath79/dts/ar9331_8dev_carambola2.dts

@@ -73,7 +73,7 @@
 
 	flash@0 {
 		compatible = "jedec,spi-nor";
-		spi-max-frequency = <104000000>;
+		spi-max-frequency = <50000000>;
 		reg = <0>;
 
 		partitions {

target/linux/ath79/dts/ar9331_embeddedwireless_dorin.dts

@@ -68,7 +68,7 @@
 
 	flash@0 {
 		compatible = "jedec,spi-nor";
-		spi-max-frequency = <104000000>;
+		spi-max-frequency = <50000000>;
 		reg = <0>;
 
 		partitions {

target/linux/ath79/dts/ar9331_tplink_tl-mr3020-v1.dts

@@ -120,7 +120,7 @@
 	/* Spansion S25FL032PIF SPI flash */
 	flash@0 {
 		compatible = "jedec,spi-nor";
-		spi-max-frequency = <104000000>;
+		spi-max-frequency = <50000000>;
 		reg = <0>;
 
 		partitions {

target/linux/ath79/dts/ar9331_tplink_tl-mr3040-v2.dts

@@ -114,7 +114,7 @@
 
 	flash@0 {
 		compatible = "jedec,spi-nor";
-		spi-max-frequency = <104000000>;
+		spi-max-frequency = <50000000>;
 		reg = <0>;
 
 		partitions {

target/linux/ath79/dts/qca9556_mikrotik_routerboard-wap-g-5hact2hnd.dts

@@ -73,7 +73,7 @@
 	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
-		spi-max-frequency = <104000000>;
+		spi-max-frequency = <50000000>;
 
 		partitions {
 			compatible = "fixed-partitions";

target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts

@@ -0,0 +1,124 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Seagate GoFlex Home";
+	compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	aliases {
+		led-boot = &led_health;
+		led-failsafe = &led_fault;
+		led-running = &led_health;
+		led-upgrade = &led_fault;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pmx_usb_power_enable: pmx-usb-power-enable {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+			pmx_led_white: pmx-led-white {
+				marvell,pins = "mpp40";
+				marvell,function = "gpio";
+			};
+			pmx_led_green: pmx-led_green {
+				marvell,pins = "mpp46";
+				marvell,function = "gpio";
+			};
+			pmx_led_orange: pmx-led-orange {
+				marvell,pins = "mpp47";
+				marvell,function = "gpio";
+			};
+		};
+		serial@12000 {
+			status = "ok";
+		};
+
+		sata@80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+
+	};
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led_health: health {
+			label = "status:green:health";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+		led_fault: fault {
+			label = "status:orange:fault";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+		misc {
+			label = "status:white:misc";
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "disk-activity";
+		};
+	};
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&nand {
+	chip-delay = <40>;
+	status = "okay";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition@100000 {
+		label = "ubi";
+		reg = <0x100000 0x0ff00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};

target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-linksys-audi.dts

@@ -0,0 +1,250 @@
+/*
+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
+ *
+ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
+ * (c) 2013 Deutsche Telekom Innovation Laboratories
+ * (c) 2014 Luka Perkov <luka@openwrt.org>
+ * (c) 2014 Dan Walters <dan@walters.io>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+	model = "Linksys Audi (EA3500)";
+	compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
+		pinctrl-names = "default";
+
+		wps {
+			label = "WPS Button";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+
+		reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = < &pmx_led_green_power >;
+		pinctrl-names = "default";
+
+		led_power: power {
+			label = "audi:green:power";
+			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	mvsw61xx {
+		compatible = "marvell,88e6171";
+		status = "okay";
+		reg = <0x10>;
+
+		mii-bus = <&mdio>;
+		cpu-port-0 = <5>;
+		cpu-port-1 = <6>;
+		is-indirect;
+	};
+
+	dsa {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		dsa,ethernet = <&eth0port>;
+		dsa,mii-bus = <&mdio>;
+
+		switch@16,0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <16 0>;	/* MDIO address 16, switch 0 in tree */
+
+			port@0 {
+				reg = <0>;
+				label = "ethernet1";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "ethernet2";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "ethernet3";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "ethernet4";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "internet";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+			};
+		};
+	};
+};
+
+&pinctrl {
+	pmx_led_green_power: pmx-led-green-power {
+		marvell,pins = "mpp7";
+		marvell,function = "gpo";
+	};
+	pmx_btn_wps: pmx-btn-wps {
+		marvell,pins = "mpp47";
+		marvell,function = "gpio";
+	};
+	pmx_btn_reset: pmx-btn-reset {
+		marvell,pins = "mpp48";
+		marvell,function = "gpio";
+	};
+};
+
+&nand {
+	status = "okay";
+	pinctrl-0 = <&pmx_nand>;
+	pinctrl-names = "default";
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "u_env";
+			reg = <0x80000 0x4000>;
+		};
+
+		partition@84000 {
+			label = "s_env";
+			reg = <0x84000 0x4000>;
+		};
+
+		partition@200000 {
+			label = "kernel1";
+			reg = <0x200000 0x290000>;
+		};
+
+		partition@490000 {
+			label = "rootfs1";
+			reg = <0x490000 0x1170000>;
+		};
+
+		partition@1600000 {
+			label = "kernel2";
+			reg = <0x1600000 0x290000>;
+		};
+
+		partition@1890000 {
+			label = "rootfs2";
+			reg = <0x1890000 0x1170000>;
+		};
+
+		partition@2a00000 {
+			label = "syscfg";
+			reg = <0x2a00000  0x1600000>;
+		};
+
+		partition@88000 {
+			label = "unused";
+			reg = <0x88000 0x178000>;
+		};
+
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
+ * fixed speed and duplex.
+ */
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+/* eth1 is connected to the switch at port 6. However DSA only supports a
+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
+ */
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+/* There is no battery on the board, so the RTC does not keep
+ * time when there is no power, making it useless.
+ */
+&rtc {
+	status = "disabled";
+};

target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-nsa310b.dts

@@ -0,0 +1,132 @@
+/dts-v1/;
+
+#include "kirkwood-nsa3x0-common.dtsi"
+
+/*
+ * There are at least two different NSA310 designs. This variant has
+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
+ */
+
+/ {
+	model = "ZyXEL NSA310b";
+	compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	aliases {
+		led-boot = &led_green_sys;
+		led-failsafe = &led_red_sys;
+		led-running = &led_green_sys;
+		led-upgrade = &led_red_sys;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-names = "default";
+
+			pmx_led_esata_green: pmx-led-esata-green {
+				marvell,pins = "mpp12";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_esata_red: pmx-led-esata-red {
+				marvell,pins = "mpp13";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_usb_green: pmx-led-usb-green {
+				marvell,pins = "mpp15";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_usb_red: pmx-led-usb-red {
+				marvell,pins = "mpp16";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_green: pmx-led-sys-green {
+				marvell,pins = "mpp28";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_red: pmx-led-sys-red {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd_green: pmx-led-hdd-green {
+				marvell,pins = "mpp41";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd_red: pmx-led-hdd-red {
+				marvell,pins = "mpp42";
+				marvell,function = "gpio";
+			};
+
+		};
+
+		i2c@11000 {
+			status = "okay";
+
+			lm85: lm85@2e {
+				compatible = "national,lm85";
+				reg = <0x2e>;
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led_green_sys: green-sys {
+			label = "nsa310:green:sys";
+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+		led_red_sys: red-sys {
+			label = "nsa310:red:sys";
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+		green-hdd {
+			label = "nsa310:green:hdd";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		};
+		red-hdd {
+			label = "nsa310:red:hdd";
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+		green-esata {
+			label = "nsa310:green:esata";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		};
+		red-esata {
+			label = "nsa310:red:esata";
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+		green-usb {
+			label = "nsa310:green:usb";
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+		};
+		red-usb {
+			label = "nsa310:red:usb";
+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+		};
+		green-copy {
+			label = "nsa310:green:copy";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+		red-copy {
+			label = "nsa310:red:copy";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};

target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-on100.dts

@@ -0,0 +1,165 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+	model = "Cisco Systems ON100";
+	compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	aliases {
+		led-boot = &led_health_green;
+		led-failsafe = &led_health_red;
+		led-running = &led_health_green;
+		led-upgrade = &led_health_red;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_btn_reset>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >;
+		pinctrl-names = "default";
+
+		led_health_green: health_green {
+			label = "on100:green:health";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led_health_red: health_red {
+			label = "on100:red:health";
+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		};
+
+		health2_green {
+			label = "on100:green:health2";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+
+		health2_red {
+			label = "on100:red:health2";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+		phy-connection-type = "rgmii-id";
+	};
+};
+
+&eth1 {
+	status = "okay";
+
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+		phy-connection-type = "rgmii-id";
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		/* Marvell 88E1121R */
+		compatible = "ethernet-phy-id0141.0cb0",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		/* Marvell 88E1121R */
+		compatible = "ethernet-phy-id0141.0cb0",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x00000000 0x000a0000>;
+		read-only;
+	};
+
+	partition@a0000 {
+		label = "u-boot environment";
+		reg = <0x000a0000 0x00020000>;
+		read-only;
+	};
+
+	partition@c0000 {
+		label = "kernel";
+		reg = <0x000c0000 0x00540000>;
+	};
+
+	partition@600000 {
+		label = "ubi";
+		reg = <0x00600000 0x1fa00000>;
+	};
+};
+
+&pinctrl {
+	pmx_led_health_r: pmx-led-health-r {
+		marvell,pins = "mpp45";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_health_g: pmx-led-health-g {
+		marvell,pins = "mpp44";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_health2_r: pmx-led-health2-r {
+		marvell,pins = "mpp47";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_health2_g: pmx-led-health2-g {
+		marvell,pins = "mpp46";
+		marvell,function = "gpio";
+	};
+
+	pmx_btn_reset: pmx-led-reset {
+		marvell,pins = "mpp31";
+		marvell,function = "gpio";
+	};
+};
+
+&sdio {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};

target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-goflexhome.dts

@@ -0,0 +1,135 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Seagate GoFlex Home";
+	compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	aliases {
+		led-boot = &led_health;
+		led-failsafe = &led_fault;
+		led-running = &led_health;
+		led-upgrade = &led_fault;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pmx_usb_power_enable: pmx-usb-power-enable {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_white: pmx-led-white {
+				marvell,pins = "mpp40";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_green: pmx-led_green {
+				marvell,pins = "mpp46";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_orange: pmx-led-orange {
+				marvell,pins = "mpp47";
+				marvell,function = "gpio";
+			};
+		};
+
+		serial@12000 {
+			status = "okay";
+		};
+
+		sata@80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led_health: health {
+			label = "status:green:health";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led_fault: fault {
+			label = "status:orange:fault";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+
+		misc {
+			label = "status:white:misc";
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "disk-activity";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+
+	chip-delay = <40>;
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0000000 0x0100000>;
+		read-only;
+	};
+
+	partition@100000 {
+		label = "ubi";
+		reg = <0x0100000 0xff00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};

target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-linksys-audi.dts

@@ -0,0 +1,257 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
+ *
+ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
+ * (c) 2013 Deutsche Telekom Innovation Laboratories
+ * (c) 2014 Luka Perkov <luka@openwrt.org>
+ * (c) 2014 Dan Walters <dan@walters.io>
+ *
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+	model = "Linksys Audi (EA3500)";
+	compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&pmx_btn_wps &pmx_btn_reset>;
+		pinctrl-names = "default";
+
+		wps {
+			label = "WPS Button";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+
+		reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&pmx_led_green_power>;
+		pinctrl-names = "default";
+
+		led_power: power {
+			label = "audi:green:power";
+			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	switches {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mvsw61xx@10 {
+			compatible = "marvell,88e6171";
+			status = "okay";
+			reg = <0x10>;
+
+			mii-bus = <&mdio>;
+			cpu-port-0 = <5>;
+			cpu-port-1 = <6>;
+			is-indirect;
+		};
+	};
+
+	dsa {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		dsa,ethernet = <&eth0port>;
+		dsa,mii-bus = <&mdio>;
+
+		switch@16,0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <16 0>;	/* MDIO address 16, switch 0 in tree */
+
+			port@0 {
+				reg = <0>;
+				label = "ethernet1";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "ethernet2";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "ethernet3";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "ethernet4";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "internet";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+			};
+		};
+	};
+};
+
+&pinctrl {
+	pmx_led_green_power: pmx-led-green-power {
+		marvell,pins = "mpp7";
+		marvell,function = "gpo";
+	};
+
+	pmx_btn_wps: pmx-btn-wps {
+		marvell,pins = "mpp47";
+		marvell,function = "gpio";
+	};
+
+	pmx_btn_reset: pmx-btn-reset {
+		marvell,pins = "mpp48";
+		marvell,function = "gpio";
+	};
+};
+
+&nand {
+	status = "okay";
+
+	pinctrl-0 = <&pmx_nand>;
+	pinctrl-names = "default";
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "u_env";
+			reg = <0x80000 0x4000>;
+		};
+
+		partition@84000 {
+			label = "s_env";
+			reg = <0x84000 0x4000>;
+		};
+
+		partition@200000 {
+			label = "kernel1";
+			reg = <0x200000 0x290000>;
+		};
+
+		partition@490000 {
+			label = "rootfs1";
+			reg = <0x490000 0x1170000>;
+		};
+
+		partition@1600000 {
+			label = "kernel2";
+			reg = <0x1600000 0x290000>;
+		};
+
+		partition@1890000 {
+			label = "rootfs2";
+			reg = <0x1890000 0x1170000>;
+		};
+
+		partition@2a00000 {
+			label = "syscfg";
+			reg = <0x2a00000  0x1600000>;
+		};
+
+		partition@88000 {
+			label = "unused";
+			reg = <0x88000 0x178000>;
+		};
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
+ * fixed speed and duplex.
+ */
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+/* eth1 is connected to the switch at port 6. However DSA only supports a
+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
+ */
+&eth1 {
+	status = "okay";
+
+	ethernet1-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+/* There is no battery on the board, so the RTC does not keep
+ * time when there is no power, making it useless.
+ */
+&rtc {
+	status = "disabled";
+};

target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-nsa310b.dts

@@ -0,0 +1,141 @@
+/dts-v1/;
+
+#include "kirkwood-nsa3x0-common.dtsi"
+
+/*
+ * There are at least two different NSA310 designs. This variant has
+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
+ */
+
+/ {
+	model = "ZyXEL NSA310b";
+	compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	aliases {
+		led-boot = &led_green_sys;
+		led-failsafe = &led_red_sys;
+		led-running = &led_green_sys;
+		led-upgrade = &led_red_sys;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-names = "default";
+
+			pmx_led_esata_green: pmx-led-esata-green {
+				marvell,pins = "mpp12";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_esata_red: pmx-led-esata-red {
+				marvell,pins = "mpp13";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_usb_green: pmx-led-usb-green {
+				marvell,pins = "mpp15";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_usb_red: pmx-led-usb-red {
+				marvell,pins = "mpp16";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_green: pmx-led-sys-green {
+				marvell,pins = "mpp28";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_red: pmx-led-sys-red {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd_green: pmx-led-hdd-green {
+				marvell,pins = "mpp41";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd_red: pmx-led-hdd-red {
+				marvell,pins = "mpp42";
+				marvell,function = "gpio";
+			};
+
+		};
+
+		i2c@11000 {
+			status = "okay";
+
+			lm85: lm85@2e {
+				compatible = "national,lm85";
+				reg = <0x2e>;
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led_green_sys: green-sys {
+			label = "nsa310:green:sys";
+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		led_red_sys: red-sys {
+			label = "nsa310:red:sys";
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+
+		green-hdd {
+			label = "nsa310:green:hdd";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		red-hdd {
+			label = "nsa310:red:hdd";
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		green-esata {
+			label = "nsa310:green:esata";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		};
+
+		red-esata {
+			label = "nsa310:red:esata";
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		green-usb {
+			label = "nsa310:green:usb";
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		red-usb {
+			label = "nsa310:red:usb";
+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		green-copy {
+			label = "nsa310:green:copy";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		red-copy {
+			label = "nsa310:red:copy";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};

target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-on100.dts

@@ -0,0 +1,165 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+	model = "Cisco Systems ON100";
+	compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	aliases {
+		led-boot = &led_health_green;
+		led-failsafe = &led_health_red;
+		led-running = &led_health_green;
+		led-upgrade = &led_health_red;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&pmx_btn_reset>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&pmx_led_health_red &pmx_led_health_green>;
+		pinctrl-names = "default";
+
+		led_health_green: health-green {
+			label = "on100:green:health";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led_health_red: health-red {
+			label = "on100:red:health";
+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		};
+
+		health2-green {
+			label = "on100:green:health2";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+
+		health2-red {
+			label = "on100:red:health2";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+		phy-connection-type = "rgmii-id";
+	};
+};
+
+&eth1 {
+	status = "okay";
+
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+		phy-connection-type = "rgmii-id";
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		/* Marvell 88E1121R */
+		compatible = "ethernet-phy-id0141.0cb0",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		/* Marvell 88E1121R */
+		compatible = "ethernet-phy-id0141.0cb0",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x00000000 0x000a0000>;
+		read-only;
+	};
+
+	partition@a0000 {
+		label = "u-boot environment";
+		reg = <0x000a0000 0x00020000>;
+		read-only;
+	};
+
+	partition@c0000 {
+		label = "kernel";
+		reg = <0x000c0000 0x00540000>;
+	};
+
+	partition@600000 {
+		label = "ubi";
+		reg = <0x00600000 0x1fa00000>;
+	};
+};
+
+&pinctrl {
+	pmx_led_health_red: pmx-led-health-red {
+		marvell,pins = "mpp45";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_health_green: pmx-led-health-green {
+		marvell,pins = "mpp44";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_health2_red: pmx-led-health2-red {
+		marvell,pins = "mpp47";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_health2_green: pmx-led-health2-green {
+		marvell,pins = "mpp46";
+		marvell,function = "gpio";
+	};
+
+	pmx_btn_reset: pmx-btn-reset {
+		marvell,pins = "mpp31";
+		marvell,function = "gpio";
+	};
+};
+
+&sdio {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};

target/linux/kirkwood/patches-4.14/104-ea3500.patch

@@ -1,263 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -250,6 +250,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-linkstation-lswsxl.dtb \
- 	kirkwood-linkstation-lswvl.dtb \
- 	kirkwood-linkstation-lswxl.dtb \
-+	kirkwood-linksys-audi.dtb \
- 	kirkwood-linksys-viper.dtb \
- 	kirkwood-lschlv2.dtb \
- 	kirkwood-lsxhl.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts
-@@ -0,0 +1,250 @@
-+/*
-+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
-+ *
-+ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
-+ * (c) 2013 Deutsche Telekom Innovation Laboratories
-+ * (c) 2014 Luka Perkov <luka@openwrt.org>
-+ * (c) 2014 Dan Walters <dan@walters.io>
-+ *
-+ * This file is licensed under the terms of the GNU General Public
-+ * License version 2.  This program is licensed "as is" without any
-+ * warranty of any kind, whether express or implied.
-+ */
-+
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+	model = "Linksys Audi (EA3500)";
-+	compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+	memory {
-+		device_type = "memory";
-+		reg = <0x00000000 0x4000000>;
-+	};
-+
-+	aliases {
-+		led-boot = &led_power;
-+		led-failsafe = &led_power;
-+		led-running = &led_power;
-+		led-upgrade = &led_power;
-+		serial0 = &uart0;
-+	};
-+
-+	chosen {
-+		stdout-path = "serial0:115200n8";
-+	};
-+
-+	gpio_keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+		pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
-+		pinctrl-names = "default";
-+
-+		wps {
-+			label = "WPS Button";
-+			linux,code = <KEY_WPS_BUTTON>;
-+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		reset {
-+			label = "Reset Button";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+		pinctrl-0 = < &pmx_led_green_power >;
-+		pinctrl-names = "default";
-+
-+		led_power: power {
-+			label = "audi:green:power";
-+			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-+			default-state = "on";
-+		};
-+	};
-+
-+	mvsw61xx {
-+		compatible = "marvell,88e6171";
-+		status = "okay";
-+		reg = <0x10>;
-+
-+		mii-bus = <&mdio>;
-+		cpu-port-0 = <5>;
-+		cpu-port-1 = <6>;
-+		is-indirect;
-+	};
-+
-+	dsa {
-+		compatible = "marvell,dsa";
-+		#address-cells = <2>;
-+		#size-cells = <0>;
-+
-+		dsa,ethernet = <&eth0port>;
-+		dsa,mii-bus = <&mdio>;
-+
-+		switch@16,0 {
-+			#address-cells = <1>;
-+			#size-cells = <0>;
-+			reg = <16 0>;	/* MDIO address 16, switch 0 in tree */
-+
-+			port@0 {
-+				reg = <0>;
-+				label = "ethernet1";
-+			};
-+
-+			port@1 {
-+				reg = <1>;
-+				label = "ethernet2";
-+			};
-+
-+			port@2 {
-+				reg = <2>;
-+				label = "ethernet3";
-+			};
-+
-+			port@3 {
-+				reg = <3>;
-+				label = "ethernet4";
-+			};
-+
-+			port@4 {
-+				reg = <4>;
-+				label = "internet";
-+			};
-+
-+			port@5 {
-+				reg = <5>;
-+				label = "cpu";
-+			};
-+		};
-+	};
-+};
-+
-+&pinctrl {
-+	pmx_led_green_power: pmx-led-green-power {
-+		marvell,pins = "mpp7";
-+		marvell,function = "gpo";
-+	};
-+	pmx_btn_wps: pmx-btn-wps {
-+		marvell,pins = "mpp47";
-+		marvell,function = "gpio";
-+	};
-+	pmx_btn_reset: pmx-btn-reset {
-+		marvell,pins = "mpp48";
-+		marvell,function = "gpio";
-+	};
-+};
-+
-+&nand {
-+	status = "okay";
-+	pinctrl-0 = <&pmx_nand>;
-+	pinctrl-names = "default";
-+
-+	partitions {
-+		compatible = "fixed-partitions";
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+
-+		partition@0 {
-+			label = "u-boot";
-+			reg = <0x0 0x80000>;
-+			read-only;
-+		};
-+
-+		partition@80000 {
-+			label = "u_env";
-+			reg = <0x80000 0x4000>;
-+		};
-+
-+		partition@84000 {
-+			label = "s_env";
-+			reg = <0x84000 0x4000>;
-+		};
-+
-+		partition@200000 {
-+			label = "kernel1";
-+			reg = <0x200000 0x290000>;
-+		};
-+
-+		partition@490000 {
-+			label = "rootfs1";
-+			reg = <0x490000 0x1170000>;
-+		};
-+
-+		partition@1600000 {
-+			label = "kernel2";
-+			reg = <0x1600000 0x290000>;
-+		};
-+
-+		partition@1890000 {
-+			label = "rootfs2";
-+			reg = <0x1890000 0x1170000>;
-+		};
-+
-+		partition@2a00000 {
-+			label = "syscfg";
-+			reg = <0x2a00000  0x1600000>;
-+		};
-+
-+		partition@88000 {
-+			label = "unused";
-+			reg = <0x88000 0x178000>;
-+		};
-+
-+	};
-+};
-+
-+&pciec {
-+	status = "okay";
-+};
-+
-+&pcie0 {
-+	status = "okay";
-+};
-+
-+&pcie1 {
-+	status = "okay";
-+};
-+
-+&mdio {
-+	status = "okay";
-+};
-+
-+&uart0 {
-+	status = "okay";
-+};
-+
-+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
-+ * fixed speed and duplex.
-+ */
-+&eth0 {
-+	status = "okay";
-+	ethernet0-port@0 {
-+		speed = <1000>;
-+		duplex = <1>;
-+	};
-+};
-+
-+/* eth1 is connected to the switch at port 6. However DSA only supports a
-+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
-+ */
-+&eth1 {
-+	status = "okay";
-+	ethernet1-port@0 {
-+		speed = <1000>;
-+		duplex = <1>;
-+	};
-+};
-+
-+/* There is no battery on the board, so the RTC does not keep
-+ * time when there is no power, making it useless.
-+ */
-+&rtc {
-+	status = "disabled";
-+};

target/linux/kirkwood/patches-4.14/105-goflexhome.patch

@@ -1,137 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -237,6 +237,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-ds411.dtb \
- 	kirkwood-ds411j.dtb \
- 	kirkwood-ds411slim.dtb \
-+	kirkwood-goflexhome.dtb \
- 	kirkwood-goflexnet.dtb \
- 	kirkwood-guruplug-server-plus.dtb \
- 	kirkwood-ib62x0.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
-@@ -0,0 +1,124 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+
-+/ {
-+	model = "Seagate GoFlex Home";
-+	compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+	aliases {
-+		led-boot = &led_health;
-+		led-failsafe = &led_fault;
-+		led-running = &led_health;
-+		led-upgrade = &led_fault;
-+	};
-+
-+	memory {
-+		device_type = "memory";
-+		reg = <0x00000000 0x8000000>;
-+	};
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
-+		stdout-path = &uart0;
-+	};
-+
-+	ocp@f1000000 {
-+		pinctrl: pin-controller@10000 {
-+			pmx_usb_power_enable: pmx-usb-power-enable {
-+				marvell,pins = "mpp29";
-+				marvell,function = "gpio";
-+			};
-+			pmx_led_white: pmx-led-white {
-+				marvell,pins = "mpp40";
-+				marvell,function = "gpio";
-+			};
-+			pmx_led_green: pmx-led_green {
-+				marvell,pins = "mpp46";
-+				marvell,function = "gpio";
-+			};
-+			pmx_led_orange: pmx-led-orange {
-+				marvell,pins = "mpp47";
-+				marvell,function = "gpio";
-+			};
-+		};
-+		serial@12000 {
-+			status = "ok";
-+		};
-+
-+		sata@80000 {
-+			status = "okay";
-+			nr-ports = <2>;
-+		};
-+
-+	};
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+
-+		led_health: health {
-+			label = "status:green:health";
-+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-+			default-state = "on";
-+		};
-+		led_fault: fault {
-+			label = "status:orange:fault";
-+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+		};
-+		misc {
-+			label = "status:white:misc";
-+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "disk-activity";
-+		};
-+	};
-+	regulators {
-+		compatible = "simple-bus";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+		pinctrl-0 = <&pmx_usb_power_enable>;
-+		pinctrl-names = "default";
-+
-+		usb_power: regulator@1 {
-+			compatible = "regulator-fixed";
-+			reg = <1>;
-+			regulator-name = "USB Power";
-+			regulator-min-microvolt = <5000000>;
-+			regulator-max-microvolt = <5000000>;
-+			enable-active-high;
-+			regulator-always-on;
-+			regulator-boot-on;
-+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+};
-+
-+&nand {
-+	chip-delay = <40>;
-+	status = "okay";
-+
-+	partition@0 {
-+		label = "u-boot";
-+		reg = <0x0000000 0x100000>;
-+		read-only;
-+	};
-+
-+	partition@100000 {
-+		label = "ubi";
-+		reg = <0x100000 0x0ff00000>;
-+	};
-+};
-+
-+&mdio {
-+	status = "okay";
-+
-+	ethphy0: ethernet-phy@0 {
-+		reg = <0>;
-+	};
-+};
-+
-+&eth0 {
-+	status = "okay";
-+	ethernet0-port@0 {
-+		phy-handle = <&ethphy0>;
-+	};
-+};

target/linux/kirkwood/patches-4.14/107-02-nsa310b.patch

@@ -1,155 +0,0 @@
-kirkwood: add nsa310b dtb, a zyxel nsa310 variant
-
-add support to a nsa310 variant with red/green usb led
-and lm85 temp/fan controller
-
-Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
-
-NOTE: this patch can be upstreamed as-is, LEDE-specific
-		nand partitions are set in another patch
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -268,6 +268,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-ns2mini.dtb \
- 	kirkwood-nsa310.dtb \
- 	kirkwood-nsa310a.dtb \
-+	kirkwood-nsa310b.dtb \
- 	kirkwood-nsa320.dtb \
- 	kirkwood-nsa325.dtb \
- 	kirkwood-openblocks_a6.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts
-@@ -0,0 +1,132 @@
-+/dts-v1/;
-+
-+#include "kirkwood-nsa3x0-common.dtsi"
-+
-+/*
-+ * There are at least two different NSA310 designs. This variant has
-+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
-+ */
-+
-+/ {
-+	model = "ZyXEL NSA310b";
-+	compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+	aliases {
-+		led-boot = &led_green_sys;
-+		led-failsafe = &led_red_sys;
-+		led-running = &led_green_sys;
-+		led-upgrade = &led_red_sys;
-+	};
-+
-+	memory {
-+		device_type = "memory";
-+		reg = <0x00000000 0x10000000>;
-+	};
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200";
-+		stdout-path = &uart0;
-+	};
-+
-+	ocp@f1000000 {
-+		pinctrl: pin-controller@10000 {
-+			pinctrl-names = "default";
-+
-+			pmx_led_esata_green: pmx-led-esata-green {
-+				marvell,pins = "mpp12";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_esata_red: pmx-led-esata-red {
-+				marvell,pins = "mpp13";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_usb_green: pmx-led-usb-green {
-+				marvell,pins = "mpp15";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_usb_red: pmx-led-usb-red {
-+				marvell,pins = "mpp16";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_sys_green: pmx-led-sys-green {
-+				marvell,pins = "mpp28";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_sys_red: pmx-led-sys-red {
-+				marvell,pins = "mpp29";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_hdd_green: pmx-led-hdd-green {
-+				marvell,pins = "mpp41";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_hdd_red: pmx-led-hdd-red {
-+				marvell,pins = "mpp42";
-+				marvell,function = "gpio";
-+			};
-+
-+		};
-+
-+		i2c@11000 {
-+			status = "okay";
-+
-+			lm85: lm85@2e {
-+				compatible = "national,lm85";
-+				reg = <0x2e>;
-+			};
-+		};
-+	};
-+
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+
-+		led_green_sys: green-sys {
-+			label = "nsa310:green:sys";
-+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+			default-state = "on";
-+		};
-+		led_red_sys: red-sys {
-+			label = "nsa310:red:sys";
-+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+		};
-+		green-hdd {
-+			label = "nsa310:green:hdd";
-+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-+		};
-+		red-hdd {
-+			label = "nsa310:red:hdd";
-+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-+		};
-+		green-esata {
-+			label = "nsa310:green:esata";
-+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
-+		};
-+		red-esata {
-+			label = "nsa310:red:esata";
-+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-+		};
-+		green-usb {
-+			label = "nsa310:green:usb";
-+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+		};
-+		red-usb {
-+			label = "nsa310:red:usb";
-+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
-+		};
-+		green-copy {
-+			label = "nsa310:green:copy";
-+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-+		};
-+		red-copy {
-+			label = "nsa310:red:copy";
-+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+};

target/linux/kirkwood/patches-4.14/108-on100.patch

@@ -1,178 +0,0 @@
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-on100.dts
-@@ -0,0 +1,165 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+	model = "Cisco Systems ON100";
-+	compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+	memory {
-+		device_type = "memory";
-+		reg = <0x00000000 0x20000000>;
-+	};
-+
-+	aliases {
-+		led-boot = &led_health_green;
-+		led-failsafe = &led_health_red;
-+		led-running = &led_health_green;
-+		led-upgrade = &led_health_red;
-+		serial0 = &uart0;
-+	};
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200n8 earlyprintk";
-+		stdout-path = "serial0:115200n8";
-+	};
-+
-+	gpio_keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+		pinctrl-0 = <&pmx_btn_reset>;
-+		pinctrl-names = "default";
-+
-+		button@1 {
-+			label = "Reset Button";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+		pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >;
-+		pinctrl-names = "default";
-+
-+		led_health_green: health_green {
-+			label = "on100:green:health";
-+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
-+			default-state = "on";
-+		};
-+
-+		led_health_red: health_red {
-+			label = "on100:red:health";
-+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		health2_green {
-+			label = "on100:green:health2";
-+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		health2_red {
-+			label = "on100:red:health2";
-+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&eth0 {
-+	status = "okay";
-+
-+	ethernet0-port@0 {
-+		phy-handle = <&ethphy0>;
-+		phy-connection-type = "rgmii-id";
-+	};
-+};
-+
-+&eth1 {
-+	status = "okay";
-+
-+	ethernet1-port@0 {
-+		phy-handle = <&ethphy1>;
-+		phy-connection-type = "rgmii-id";
-+	};
-+};
-+
-+&mdio {
-+	status = "okay";
-+
-+	ethphy0: ethernet-phy@0 {
-+		/* Marvell 88E1121R */
-+		compatible = "ethernet-phy-id0141.0cb0",
-+			     "ethernet-phy-ieee802.3-c22";
-+		reg = <0>;
-+	};
-+
-+	ethphy1: ethernet-phy@1 {
-+		/* Marvell 88E1121R */
-+		compatible = "ethernet-phy-id0141.0cb0",
-+			     "ethernet-phy-ieee802.3-c22";
-+		reg = <1>;
-+	};
-+};
-+
-+&nand {
-+	status = "okay";
-+
-+	partition@0 {
-+		label = "u-boot";
-+		reg = <0x00000000 0x000a0000>;
-+		read-only;
-+	};
-+
-+	partition@a0000 {
-+		label = "u-boot environment";
-+		reg = <0x000a0000 0x00020000>;
-+		read-only;
-+	};
-+
-+	partition@c0000 {
-+		label = "kernel";
-+		reg = <0x000c0000 0x00540000>;
-+	};
-+
-+	partition@600000 {
-+		label = "ubi";
-+		reg = <0x00600000 0x1fa00000>;
-+	};
-+};
-+
-+&pinctrl {
-+	pmx_led_health_r: pmx-led-health-r {
-+		marvell,pins = "mpp45";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_led_health_g: pmx-led-health-g {
-+		marvell,pins = "mpp44";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_led_health2_r: pmx-led-health2-r {
-+		marvell,pins = "mpp47";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_led_health2_g: pmx-led-health2-g {
-+		marvell,pins = "mpp46";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_btn_reset: pmx-led-reset {
-+		marvell,pins = "mpp31";
-+		marvell,function = "gpio";
-+	};
-+};
-+
-+&sdio {
-+	status = "okay";
-+};
-+
-+&uart0 {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -271,6 +271,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-nsa310b.dtb \
- 	kirkwood-nsa320.dtb \
- 	kirkwood-nsa325.dtb \
-+	kirkwood-on100.dtb \
- 	kirkwood-openblocks_a6.dtb \
- 	kirkwood-openblocks_a7.dtb \
- 	kirkwood-openrd-base.dtb \

target/linux/kirkwood/patches-4.19/104-ea3500.patch

@@ -1,264 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -269,6 +269,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-linkstation-lswsxl.dtb \
- 	kirkwood-linkstation-lswvl.dtb \
- 	kirkwood-linkstation-lswxl.dtb \
-+	kirkwood-linksys-audi.dtb \
- 	kirkwood-linksys-viper.dtb \
- 	kirkwood-lschlv2.dtb \
- 	kirkwood-lsxhl.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts
-@@ -0,0 +1,251 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
-+ *
-+ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
-+ * (c) 2013 Deutsche Telekom Innovation Laboratories
-+ * (c) 2014 Luka Perkov <luka@openwrt.org>
-+ * (c) 2014 Dan Walters <dan@walters.io>
-+ *
-+ */
-+
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+	model = "Linksys Audi (EA3500)";
-+	compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+	memory@0 {
-+		device_type = "memory";
-+		reg = <0x00000000 0x4000000>;
-+	};
-+
-+	aliases {
-+		led-boot = &led_power;
-+		led-failsafe = &led_power;
-+		led-running = &led_power;
-+		led-upgrade = &led_power;
-+		serial0 = &uart0;
-+	};
-+
-+	chosen {
-+		stdout-path = "serial0:115200n8";
-+	};
-+
-+	gpio_keys {
-+		compatible = "gpio-keys";
-+		pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
-+		pinctrl-names = "default";
-+
-+		wps {
-+			label = "WPS Button";
-+			linux,code = <KEY_WPS_BUTTON>;
-+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		reset {
-+			label = "Reset Button";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+		pinctrl-0 = < &pmx_led_green_power >;
-+		pinctrl-names = "default";
-+
-+		led_power: power {
-+			label = "audi:green:power";
-+			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-+			default-state = "on";
-+		};
-+	};
-+
-+	switches {
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		mvsw61xx@10 {
-+			compatible = "marvell,88e6171";
-+			status = "okay";
-+			reg = <0x10>;
-+
-+			mii-bus = <&mdio>;
-+			cpu-port-0 = <5>;
-+			cpu-port-1 = <6>;
-+			is-indirect;
-+		};
-+	};
-+
-+	dsa {
-+		compatible = "marvell,dsa";
-+		#address-cells = <2>;
-+		#size-cells = <0>;
-+
-+		dsa,ethernet = <&eth0port>;
-+		dsa,mii-bus = <&mdio>;
-+
-+		switch@16,0 {
-+			#address-cells = <1>;
-+			#size-cells = <0>;
-+			reg = <16 0>;	/* MDIO address 16, switch 0 in tree */
-+
-+			port@0 {
-+				reg = <0>;
-+				label = "ethernet1";
-+			};
-+
-+			port@1 {
-+				reg = <1>;
-+				label = "ethernet2";
-+			};
-+
-+			port@2 {
-+				reg = <2>;
-+				label = "ethernet3";
-+			};
-+
-+			port@3 {
-+				reg = <3>;
-+				label = "ethernet4";
-+			};
-+
-+			port@4 {
-+				reg = <4>;
-+				label = "internet";
-+			};
-+
-+			port@5 {
-+				reg = <5>;
-+				label = "cpu";
-+			};
-+		};
-+	};
-+};
-+
-+&pinctrl {
-+	pmx_led_green_power: pmx-led-green-power {
-+		marvell,pins = "mpp7";
-+		marvell,function = "gpo";
-+	};
-+	pmx_btn_wps: pmx-btn-wps {
-+		marvell,pins = "mpp47";
-+		marvell,function = "gpio";
-+	};
-+	pmx_btn_reset: pmx-btn-reset {
-+		marvell,pins = "mpp48";
-+		marvell,function = "gpio";
-+	};
-+};
-+
-+&nand {
-+	status = "okay";
-+	pinctrl-0 = <&pmx_nand>;
-+	pinctrl-names = "default";
-+
-+	partitions {
-+		compatible = "fixed-partitions";
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+
-+		partition@0 {
-+			label = "u-boot";
-+			reg = <0x0 0x80000>;
-+			read-only;
-+		};
-+
-+		partition@80000 {
-+			label = "u_env";
-+			reg = <0x80000 0x4000>;
-+		};
-+
-+		partition@84000 {
-+			label = "s_env";
-+			reg = <0x84000 0x4000>;
-+		};
-+
-+		partition@200000 {
-+			label = "kernel1";
-+			reg = <0x200000 0x290000>;
-+		};
-+
-+		partition@490000 {
-+			label = "rootfs1";
-+			reg = <0x490000 0x1170000>;
-+		};
-+
-+		partition@1600000 {
-+			label = "kernel2";
-+			reg = <0x1600000 0x290000>;
-+		};
-+
-+		partition@1890000 {
-+			label = "rootfs2";
-+			reg = <0x1890000 0x1170000>;
-+		};
-+
-+		partition@2a00000 {
-+			label = "syscfg";
-+			reg = <0x2a00000  0x1600000>;
-+		};
-+
-+		partition@88000 {
-+			label = "unused";
-+			reg = <0x88000 0x178000>;
-+		};
-+
-+	};
-+};
-+
-+&pciec {
-+	status = "okay";
-+};
-+
-+&pcie0 {
-+	status = "okay";
-+};
-+
-+&pcie1 {
-+	status = "okay";
-+};
-+
-+&mdio {
-+	status = "okay";
-+};
-+
-+&uart0 {
-+	status = "okay";
-+};
-+
-+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
-+ * fixed speed and duplex.
-+ */
-+&eth0 {
-+	status = "okay";
-+	ethernet0-port@0 {
-+		speed = <1000>;
-+		duplex = <1>;
-+	};
-+};
-+
-+/* eth1 is connected to the switch at port 6. However DSA only supports a
-+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
-+ */
-+&eth1 {
-+	status = "okay";
-+	ethernet1-port@0 {
-+		speed = <1000>;
-+		duplex = <1>;
-+	};
-+};
-+
-+/* There is no battery on the board, so the RTC does not keep
-+ * time when there is no power, making it useless.
-+ */
-+&rtc {
-+	status = "disabled";
-+};

target/linux/kirkwood/patches-4.19/105-goflexhome.patch

@@ -1,137 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -256,6 +256,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-ds411.dtb \
- 	kirkwood-ds411j.dtb \
- 	kirkwood-ds411slim.dtb \
-+	kirkwood-goflexhome.dtb \
- 	kirkwood-goflexnet.dtb \
- 	kirkwood-guruplug-server-plus.dtb \
- 	kirkwood-ib62x0.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
-@@ -0,0 +1,124 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+
-+/ {
-+	model = "Seagate GoFlex Home";
-+	compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+	aliases {
-+		led-boot = &led_health;
-+		led-failsafe = &led_fault;
-+		led-running = &led_health;
-+		led-upgrade = &led_fault;
-+	};
-+
-+	memory@0 {
-+		device_type = "memory";
-+		reg = <0x00000000 0x8000000>;
-+	};
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
-+		stdout-path = &uart0;
-+	};
-+
-+	ocp@f1000000 {
-+		pinctrl: pin-controller@10000 {
-+			pmx_usb_power_enable: pmx-usb-power-enable {
-+				marvell,pins = "mpp29";
-+				marvell,function = "gpio";
-+			};
-+			pmx_led_white: pmx-led-white {
-+				marvell,pins = "mpp40";
-+				marvell,function = "gpio";
-+			};
-+			pmx_led_green: pmx-led_green {
-+				marvell,pins = "mpp46";
-+				marvell,function = "gpio";
-+			};
-+			pmx_led_orange: pmx-led-orange {
-+				marvell,pins = "mpp47";
-+				marvell,function = "gpio";
-+			};
-+		};
-+		serial@12000 {
-+			status = "ok";
-+		};
-+
-+		sata@80000 {
-+			status = "okay";
-+			nr-ports = <2>;
-+		};
-+
-+	};
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+
-+		led_health: health {
-+			label = "status:green:health";
-+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-+			default-state = "on";
-+		};
-+		led_fault: fault {
-+			label = "status:orange:fault";
-+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+		};
-+		misc {
-+			label = "status:white:misc";
-+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "disk-activity";
-+		};
-+	};
-+	regulators {
-+		compatible = "simple-bus";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+		pinctrl-0 = <&pmx_usb_power_enable>;
-+		pinctrl-names = "default";
-+
-+		usb_power: regulator@1 {
-+			compatible = "regulator-fixed";
-+			reg = <1>;
-+			regulator-name = "USB Power";
-+			regulator-min-microvolt = <5000000>;
-+			regulator-max-microvolt = <5000000>;
-+			enable-active-high;
-+			regulator-always-on;
-+			regulator-boot-on;
-+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+};
-+
-+&nand {
-+	chip-delay = <40>;
-+	status = "okay";
-+
-+	partition@0 {
-+		label = "u-boot";
-+		reg = <0x0000000 0x100000>;
-+		read-only;
-+	};
-+
-+	partition@100000 {
-+		label = "ubi";
-+		reg = <0x100000 0x0ff00000>;
-+	};
-+};
-+
-+&mdio {
-+	status = "okay";
-+
-+	ethphy0: ethernet-phy@0 {
-+		reg = <0>;
-+	};
-+};
-+
-+&eth0 {
-+	status = "okay";
-+	ethernet0-port@0 {
-+		phy-handle = <&ethphy0>;
-+	};
-+};

target/linux/kirkwood/patches-4.19/107-02-nsa310b.patch

@@ -1,155 +0,0 @@
-kirkwood: add nsa310b dtb, a zyxel nsa310 variant
-
-add support to a nsa310 variant with red/green usb led
-and lm85 temp/fan controller
-
-Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
-
-NOTE: this patch can be upstreamed as-is, LEDE-specific
-		nand partitions are set in another patch
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -287,6 +287,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-ns2mini.dtb \
- 	kirkwood-nsa310.dtb \
- 	kirkwood-nsa310a.dtb \
-+	kirkwood-nsa310b.dtb \
- 	kirkwood-nsa320.dtb \
- 	kirkwood-nsa325.dtb \
- 	kirkwood-openblocks_a6.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts
-@@ -0,0 +1,132 @@
-+/dts-v1/;
-+
-+#include "kirkwood-nsa3x0-common.dtsi"
-+
-+/*
-+ * There are at least two different NSA310 designs. This variant has
-+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
-+ */
-+
-+/ {
-+	model = "ZyXEL NSA310b";
-+	compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+	aliases {
-+		led-boot = &led_green_sys;
-+		led-failsafe = &led_red_sys;
-+		led-running = &led_green_sys;
-+		led-upgrade = &led_red_sys;
-+	};
-+
-+	memory@0 {
-+		device_type = "memory";
-+		reg = <0x00000000 0x10000000>;
-+	};
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200";
-+		stdout-path = &uart0;
-+	};
-+
-+	ocp@f1000000 {
-+		pinctrl: pin-controller@10000 {
-+			pinctrl-names = "default";
-+
-+			pmx_led_esata_green: pmx-led-esata-green {
-+				marvell,pins = "mpp12";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_esata_red: pmx-led-esata-red {
-+				marvell,pins = "mpp13";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_usb_green: pmx-led-usb-green {
-+				marvell,pins = "mpp15";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_usb_red: pmx-led-usb-red {
-+				marvell,pins = "mpp16";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_sys_green: pmx-led-sys-green {
-+				marvell,pins = "mpp28";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_sys_red: pmx-led-sys-red {
-+				marvell,pins = "mpp29";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_hdd_green: pmx-led-hdd-green {
-+				marvell,pins = "mpp41";
-+				marvell,function = "gpio";
-+			};
-+
-+			pmx_led_hdd_red: pmx-led-hdd-red {
-+				marvell,pins = "mpp42";
-+				marvell,function = "gpio";
-+			};
-+
-+		};
-+
-+		i2c@11000 {
-+			status = "okay";
-+
-+			lm85: lm85@2e {
-+				compatible = "national,lm85";
-+				reg = <0x2e>;
-+			};
-+		};
-+	};
-+
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+
-+		led_green_sys: green-sys {
-+			label = "nsa310:green:sys";
-+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+			default-state = "on";
-+		};
-+		led_red_sys: red-sys {
-+			label = "nsa310:red:sys";
-+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+		};
-+		green-hdd {
-+			label = "nsa310:green:hdd";
-+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-+		};
-+		red-hdd {
-+			label = "nsa310:red:hdd";
-+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-+		};
-+		green-esata {
-+			label = "nsa310:green:esata";
-+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
-+		};
-+		red-esata {
-+			label = "nsa310:red:esata";
-+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-+		};
-+		green-usb {
-+			label = "nsa310:green:usb";
-+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+		};
-+		red-usb {
-+			label = "nsa310:red:usb";
-+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
-+		};
-+		green-copy {
-+			label = "nsa310:green:copy";
-+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-+		};
-+		red-copy {
-+			label = "nsa310:red:copy";
-+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+};

target/linux/kirkwood/patches-4.19/108-on100.patch

@@ -1,176 +0,0 @@
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-on100.dts
-@@ -0,0 +1,163 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+	model = "Cisco Systems ON100";
-+	compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+	memory@0 {
-+		device_type = "memory";
-+		reg = <0x00000000 0x20000000>;
-+	};
-+
-+	aliases {
-+		led-boot = &led_health_green;
-+		led-failsafe = &led_health_red;
-+		led-running = &led_health_green;
-+		led-upgrade = &led_health_red;
-+		serial0 = &uart0;
-+	};
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200n8 earlyprintk";
-+		stdout-path = "serial0:115200n8";
-+	};
-+
-+	gpio_keys {
-+		compatible = "gpio-keys";
-+		pinctrl-0 = <&pmx_btn_reset>;
-+		pinctrl-names = "default";
-+
-+		reset {
-+			label = "Reset Button";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+		pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >;
-+		pinctrl-names = "default";
-+
-+		led_health_green: health_green {
-+			label = "on100:green:health";
-+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
-+			default-state = "on";
-+		};
-+
-+		led_health_red: health_red {
-+			label = "on100:red:health";
-+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		health2_green {
-+			label = "on100:green:health2";
-+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		health2_red {
-+			label = "on100:red:health2";
-+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&eth0 {
-+	status = "okay";
-+
-+	ethernet0-port@0 {
-+		phy-handle = <&ethphy0>;
-+		phy-connection-type = "rgmii-id";
-+	};
-+};
-+
-+&eth1 {
-+	status = "okay";
-+
-+	ethernet1-port@0 {
-+		phy-handle = <&ethphy1>;
-+		phy-connection-type = "rgmii-id";
-+	};
-+};
-+
-+&mdio {
-+	status = "okay";
-+
-+	ethphy0: ethernet-phy@0 {
-+		/* Marvell 88E1121R */
-+		compatible = "ethernet-phy-id0141.0cb0",
-+			     "ethernet-phy-ieee802.3-c22";
-+		reg = <0>;
-+	};
-+
-+	ethphy1: ethernet-phy@1 {
-+		/* Marvell 88E1121R */
-+		compatible = "ethernet-phy-id0141.0cb0",
-+			     "ethernet-phy-ieee802.3-c22";
-+		reg = <1>;
-+	};
-+};
-+
-+&nand {
-+	status = "okay";
-+
-+	partition@0 {
-+		label = "u-boot";
-+		reg = <0x00000000 0x000a0000>;
-+		read-only;
-+	};
-+
-+	partition@a0000 {
-+		label = "u-boot environment";
-+		reg = <0x000a0000 0x00020000>;
-+		read-only;
-+	};
-+
-+	partition@c0000 {
-+		label = "kernel";
-+		reg = <0x000c0000 0x00540000>;
-+	};
-+
-+	partition@600000 {
-+		label = "ubi";
-+		reg = <0x00600000 0x1fa00000>;
-+	};
-+};
-+
-+&pinctrl {
-+	pmx_led_health_r: pmx-led-health-r {
-+		marvell,pins = "mpp45";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_led_health_g: pmx-led-health-g {
-+		marvell,pins = "mpp44";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_led_health2_r: pmx-led-health2-r {
-+		marvell,pins = "mpp47";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_led_health2_g: pmx-led-health2-g {
-+		marvell,pins = "mpp46";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_btn_reset: pmx-led-reset {
-+		marvell,pins = "mpp31";
-+		marvell,function = "gpio";
-+	};
-+};
-+
-+&sdio {
-+	status = "okay";
-+};
-+
-+&uart0 {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -290,6 +290,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-nsa310b.dtb \
- 	kirkwood-nsa320.dtb \
- 	kirkwood-nsa325.dtb \
-+	kirkwood-on100.dtb \
- 	kirkwood-openblocks_a6.dtb \
- 	kirkwood-openblocks_a7.dtb \
- 	kirkwood-openrd-base.dtb \